VESPA PX 150 USA Workshop Manual Download

Page: 54 / 138

−

After removing the rear cover, release the brush

clips connected to the magnetic fields.

−

Remove the brush plate. Detach the old brushes

and weld a new set of brushes, hence replace the

brush plate.

−

After removing the rear cover, detach the drive

gear retaining pin and remove the gear.

−

Refit the assembly components in the reverse

order.

Removing the flywheel magneto

−

Retain the flywheel using the special tool, hence

remove the lock nut.

Specific tooling

020095Y

Flywheel retaining tool

−

Remove the flywheel retaining tool.

−

Extract the flywheel using the special extractor.

Specific tooling

008564Y

Flywheel extractor

Engine

Vespa PX 150 USA

ENG - 54

Summary of Contents for PX 150 USA











































































































































Search results

Summary of Contents for PX 150 USA

Reviews:

Related manuals for PX 150 USA

Brands by name

Popular brands

VESPA PX 150 USA, Workshop Manual

Search results

Summary of Contents for PX 150 USA

Reviews:

Related manuals for PX 150 USA

Brands by name

Popular brands