VESPA 946 E4 EMEA 2021 Manual Download

Page: 25 / 283

Vehicle identification

Identification registration numbers are made up of a prefix and a number, stamped on the frame and

on the engine. The serial number must always be indicated when ordering spare parts. We recommend

checking that the frame registration number stamped on the vehicle corresponds with that on the vehicle

documentation.

CAUTION

PLEASE REMIND THAT ALTERING IDENTIFICATION REGISTRATION NUMBERS CAN LEAD TO
SERIOUS PENAL SANCTIONS (IMPOUNDING OF THE VEHICLE, ETC.).

Frame number

To read the chassis number «

» the saddle must

be lifted.

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Technical Data

DT - 25

Summary of Contents for 946 E4 EMEA 2021




























































































































































































































































































Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands

VESPA 946 E4 EMEA 2021, Manual

Search results

Summary of Contents for 946 E4 EMEA 2021

Reviews:

Related manuals for 946 E4 EMEA 2021

Brands by name

Popular brands