VESDA VESDA-E VES-A00-P Product Manual Download Page 39 | Manualshive

Page: 39 / 124

background image

VESDA-E VES-A00-P Product Guide

www.xtralis.com

33

4.3

Wiring

The screw type terminals located on electrical terminals within the VES-A00-P detector will accept wire sizes
from 0.2 mm² to 2.5 mm² (24 – 14 AWG).

Refer to Codes and Standards Information for Air Sampling Smoke Detection on page iii for code specific
requirements.

Refer to the VESDA-E System Design Manual for cabling details.

Note:

The VES-A00-P detector is IP 40 rated, therefore a suitable cable gland or conduit must be used to
maintain the IP rating. (The IP rating is not UL tested.)

Caution:

Electrostatic discharge (ESD) precautions need to be taken prior to removing the fascia from
the detector in order to prevent damage to sensitive electronic components within the VES-A00-
P.

Attention :

Les precausions contre le decharge electrostatique dois etre respecter avant d’ouvrir le panneau
du detecteur afin de prevenir au dommage des composants electroniques a l’interieur du VES-
A00-P.

4.3.1

Cabling Inlets

The VESDA-E VES-A00-P contains four inlets for power, relay and network cabling, located on the upper and
lower sides of the detector base. The holes have a diameter of 26 mm (1.02 inch).

Note:

To maintain the specified IP rating, cable glands or conduit must be used.

Figure 4-32: Cabling Inlets

«
...
37
38
39
40
41
...
»

Summary of Contents for VESDA-E VES-A00-P





























































































































Reviews:

No comments

Related manuals for VESDA-E VES-A00-P

Electronic Micro Alarm

Brand: Pacific GSM Pages: 4

Brand: SILENT KNIGHT Pages: 238

Brand: Hama Pages: 96

Stack CM155-045

Brand: Charmate Pages: 12

Brand: Trevi Pages: 9

Brand: philippi Pages: 6

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Smart Sound Controlled Cloud Alarm Clock

Brand: MUID Pages: 4

Brand: Toyota Pages: 23

CRA54 - Digital Alarm Clock

Brand: Coby Pages: 1

Brand: Accurite Pages: 16

Brand: Polarstart Pages: 15

Prestige Platinum APS-510C

Brand: Prestige Pages: 16

Brand: Eurotops Pages: 8

Brand: Eurotops Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands