Vescent ICE Oem Integration Manual Download | Manualshive

Page: 12 / 17

background image

Last update: 2014/07/30 18:37

ice:oem_integration http://www.vescent.com/manuals/doku.php?id=ice:oem_integration

http://www.vescent.com/manuals/

Printed on 2019/05/01 00:16

Fig. 10: Surface mount, 12-pin, 1.00 mm pitch, bottom contact FFC connector. FCI PN:
SFW12R-1STE1LF

Fig. 11: FFC jumper cable, 12-pin, 1.00 mm pitch. Molex PN: 0210390269

SMA Connector

These board edge SMA connectors (

Emerson PN: 142-0701-881

)are used on the

for handling

high frequency RF signals (>8 GHz).

«
...
10
11
12
13
14
...
»

Summary of Contents for ICE


















Reviews:

No comments

Related manuals for ICE

Univerge SV8100

Brand: NEC Pages: 2

Brand: Warner Electric Pages: 3

Brand: iCeeO2 Pages: 7

Brand: SABAF Pages: 6

Brand: Echelon Pages: 40

Brand: Samson Pages: 20

Brand: iluminize Pages: 2

Brand: JASTEC Pages: 18

Brand: SMC Networks Pages: 15

Brand: Riello Pages: 72

SystemRoMedic EvaDrive450

Brand: Handicare Pages: 37

TrueAlarm 4100 Series

Brand: Simplex Pages: 8

Brand: IFM Pages: 41

Brand: Duco Pages: 16

Brand: Digiplex Pages: 48

Brand: Moog Pages: 15

Brand: Invacare Pages: 44

Brand: FONESTAR Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands