Occupancy Sensor – Ceiling Mounted • Installation Guide
page 4 of 4
Verve™ Living Systems
© 2011 LHMC, A Masco Company
140 Business Park Drive, Winston-Salem, NC 27107
XOSC01IS01A
vervelivingsystems.com
Installing Supplemental Battery
(optional)
If light levels are very low where the sensor is installed, auxiliary
battery power (CR2032) can be used to supplement the solar
energy harvester.
1.
Remove the sensor from the mounting plate.
With the 2-button interface facing you, slide the sensor to
the right.
2.
Turn the sensor over and identify the battery holder on the
circuit board.
3.
Insert the battery under the clip with the positive pole (+)
up and press it in place.
4.
Remount the sensor on the mounting plate.
Troubleshooting
FCC SZV-STM300C
I.C. 5713A-STM300C
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Limited Warranty
Verve™ Products Limited Warranty. Subject to the other terms of this warranty, Liberty
Hardware Mfg. Corp. (“Liberty Hardware”) warrants you the original purchaser that
this Verve™ product will be free from defects in material and workmanship for five
years from the date of your purchase of the product. During that period, if the product
does not comply with this limited warranty, Liberty Hardware will, at its discretion,
repair or replace the product. Repair or replacement is your sole remedy under this or
any other warranty of the product, whether express or implied.
Coverage Limitations. This limited warranty extends only to the original purchaser and
is not transferable. This limited warranty expressly excludes any defects or damages
resulting from any product installed improperly or in an improper environment,
overloaded, misused, opened, abused, or altered in any manner.
Instructions for Warranty Service. To obtain warranty service return the Verve™
product, a description of the problem, together with your proof of purchase, securely
packaged and with postage prepaid, to:
Liberty Hardware Mfg. Corp.
Attn: Customer Service - Verve Living Systems
140 Business Park Drive
Winston Salem NC 27107
You may be required to provide other information or evidence of the defect. Any
returned product that is replaced becomes the property of Liberty Hardware.
Implied Warranties. TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED
WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE SAME DURATION AS THIS
EXPRESS WARRANTY. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. NO OTHER EXPRESS
WARRANTY HAS BEEN MADE OR WILL BE MADE BY LIBERTY HARDWARE MFG.
CORP. WITH RESPECT TO THIS PRODUCT.
Limitation of Liability. LIBERTY HARDWARE SHALL NOT BE RESPONSIBLE FOR
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS THE COST OF
LABOR FOR REMOVAL OR REINSTALLATION OF THE PRODUCT, WHETHER ARISING
OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion of incidental or consequential damages, so the
above exclusion and limitation may not apply to you.
If you have any questions about this warranty, contact us at 1-877-874-8774.
This limited warranty gives you specific legal rights, and you also may have other
rights which vary from state to state. In Canada, the above provisions are not intended
to operate where prohibited by law and do not preclude the operation of any
applicable provisional consumer protection statute which in certain circumstances
may extend the express warranties herein.
Problem
Solution Checklist
The sensor does not
generate a wireless
message
• Verify the LED blinks when motion is
detected
• Verify the solar cell is charged
properly
The sensor is activated
when there is nothing to
detect
• Verify there is 4 ft. (1.2m) clearance
from heat sources that may disturb
sensing
• Reduce the sensitivity setting by
moving the switch on the back of
the sensor to the left-hand position
The linked device does
not respond to wireless
messages
• Check for environment or range
issues
• Verify the device is linked
• Check the transceiver connection
and the wiring for errors
• Check if appropriate devices are
linked according to good system
planning
Battery
clip
Sensitivity
switch
Summary of Contents for VOSC
Page 3: ......
