Vertiv Liebert Mini-Mate MT036 Installer/User Manual Download Page 44

Page: 44 / 80

WARNING! Risk of electric shock. Can cause injury or death. The DIP switches must be set

exactly as indicated in 9.4.3 on the previous page. Failure to correctly set the DIP switches may

result in an electrical or water hazard.

The DIP switch sets the capacity of the humidifier. If you replace the humidifier, set the DIP switches on

the circuit board based on the voltage and capacity of your unit shown in Table 9.3 below.

Voltage

SW1

SW2

SW3

SW4

Amps

3-ton Units

208/230

Off

6.4

460

Off

3.4

4-ton and 5-ton Units

208

Off

8.9

240

Off

8.5

460

Off

4.5

575

Off

3.4

Table 9.3 DIP switch settings for humidifier control board

9.4.4 Humidifier Troubleshooting

Symptom

Possible Cause

Check or Remedy

Humidifier

does not

operate

DIP switch not set to

enable humidifier option

See DIP-switch settings in Table 9.3 above.

Display does not show

humidification mode

Increase humidity-control setpoint

Defective board

Check the voltage at P35-1 on the unit's iCOM board, and P1-9 and P1-7 on the

humidifier-interface board for 24 VAC ±2 VAC.

If no voltage is detected, check wiring and/or replace board. Check the wiring from the

iCOM board to the humidifier-interface board.

Failed humidity sensor

Display shows "RET sensor invalid" warning. Check wiring from the

temperature/humidity board to the control board. Replace temperature/humidity

sensor if defective.

No water flow

Make sure that the switch is in "RUN" position. Check the humidifier water (including

filter screen) and check the nylon overflow line if the canister is full.

Canister fill rate does not

keep up with steam

output

Check the fill-valve screen opening and capillary tube for obstructions. Check the

water-supply pressure (minimum 10 psig).

Table 9.4 Steam generating humidifier troubleshooting guide

9.5 Condensate-drain and Condensate-pump System Maintenance

9.5.1 Condensate Drain

Check for and clear obstructions in tubing during routine maintenance.

Vertiv | Liebert® Mini-Mate™ Installer/User Guide

Summary of Contents for Liebert Mini-Mate MT036

















































































Search results

Summary of Contents for Liebert Mini-Mate MT036

Reviews:

Vertiv Liebert Mini-Mate MT036, Installer/User Manual, Page: 44 / 80

Search results

Summary of Contents for Liebert Mini-Mate MT036

Reviews: