Vertex Standard VX-537 Operating Manual Download Page 22

Page: 22 / 24

Page 20

VX-537 Operating Manual

ccessorIes

& o

ptIons

MH-50

C7A

Speaker/Microphone

FNB-29A

7.2 V/1700 mAh Ni-Cd Battery Pack

FNB-29AL

7.2 V/1700 mAh Ni-Cd Battery Pack (Long Size)

FNB-29AIS

7.2 V/1700 mAh Ni-Cd Battery Pack

(Intrinsically Safe Battery)

FNB-29ALIS

7.2 V/1700 mAh Ni-Cd Battery Pack

(Intrinsically Safe Battery: Long Size)

FNB-29BNIS

7.2 V/2450 mAh Ni-MH Battery Pack

(Intrinsically Safe Battery)

VAC-520B

Rapid Desktop Charger (120 VAC)

VAC-520C

Rapid Desktop Charger (240 VAC)

VAC-6520

Rapid 6-Unit Multi Charger

CD-10

Rapid Vehicular Charger

VCM-1

Mobile Mounting Bracket for VAC-520

CS-500B

Overnight Desktop Charger (120 VAC)

CS-500C

Overnight Desktop Charger (240 VAC)

FBA-19

6 AA Size Battery Case

ATU-5D

UHF Antenna (450 ~ 470 MHz)

ATU-5EF

UHF Antenna (470 ~ 490 MHz)

FVP-25

Encryption Unit

F2D-8

2-Tone Sequential Decoder Unit

F5D-14

5-Tone Sequential Decoder Unit

CE65

Radio to Computer Programming Software

SVC65

Alignment Software

CT-71

Radio to Computer Programming Cable

CT-72

Radio to Radio Programming Cable

VTP-50

VX-Trunk II VX-Trunking Portable Logic Board

CLIP-2

Belt Clip

SBC-1

Swivel Belt Adaptor (Requires LCS-2)

LCS-2

Swivel Belt Attachment

CN-7

Antenna Jack Adaptor (Stud to BNC)

The following optional units are not available for intrinsically safe use,

because they do not have an IS rating. If any of the optional units listed

below is used with the VX-537, the radio is no longer intrinsically safe,

and must not be used in hazardous locations.

Battery Packs:

FNB-29A

and

FNB-29AL

Alkaline Battery Tray:

FBA-19

5-Tone Sequential Decoder Unit:

F5D-14

Summary of Contents for VX-537
























Search results

Summary of Contents for VX-537

Reviews:

Related manuals for VX-537

Brands by name

Popular brands

Vertex Standard VX-537, Operating Manual

Search results

Summary of Contents for VX-537

Reviews:

Related manuals for VX-537

Brands by name

Popular brands