Versitron SG24816M User Manual Download Page 237

Page: 237 / 241

User Manual

229

www.versitron.com

SG24816M

Hardware Specifications

Standard Compliance:

IEEE802.3/802.3ab / 802.3z / 802.3u / 802.3x

Network Interface:

Configuration

Mode

Connector

Port

10/100/1000Mbps Gigabit TP

NWay

TP (RJ-45)

1 - 8

1000Base-SX Gigabit Fiber

1000 FDX

*SFP

9 - 24

1000Base-LX Gigabit Fiber

1000 FDX

*SFP

9 - 24

1000Base-LX Single Fiber WDM (BiDi) 1000 FDX

*SFP

9 - 24

*Optional SFP module supports LC or BiDi LC transceiver

Transmission Mode:

10/100Mbps support full or half duplex

1000Mbps support full duplex only

Transmission Speed:

10/100/1000Mbps for TP

1000Mbps for Fiber

Full Forwarding/Filtering Packet Rate:

PPS (packets per second)

Forwarding Rate

Speed

1,488,000PPS 1000Mbps
148,800PPS 100Mbps
14,880PPS 10Mbps

MAC Address and Self-learning:

8K MAC address

4K VLAN table entries,

Buffer Memory:

Embedded 400 KB frame buffer

Flow Control:

IEEE802.3x compliant for full duplex

Backpressure flow control for half duplex

Cable and Maximum Length:

Cat. 5 UTP cable, up to 100m

1000Base-SX

Up to 220/275/500/550m,
which depends on Multi-Mode Fiber type

1000Base-LX

Single-Mode Fiber, up to10/30/50Km

1000Base-LX WDM (BiDi)

Single-Mode Single Fiber, up to 20Km

Summary of Contents for SG24816M


















































































































































































































































Search results

Summary of Contents for SG24816M

Reviews:

Versitron SG24816M, User Manual, Page: 237 / 241

Search results

Summary of Contents for SG24816M

Reviews: