manualshive.com logo in svg

Versatile AutoBoom SX275, Installation Manual

Share
Download
Versatile AutoBoom SX275 Installation Manual Download Page 50

Chapter 4

46

Versatile SX275 AutoBoom™ Installation Manual

3.

Install a center rack control boom sense adapter cable (P/N 115-0230-039) on the machine’s up coil.

4.

Connect the coil connector to the installed boom sense adapter cable.

5.

Connect the connectors on the installed boom sense adapter cable to the CENTER UP harness connectors 
on the AutoBoom harness cable (P/N 115-0230-033).

6.

Locate the center down coil on the machine’s hydraulic valve.

7.

Unplug the coil connector from the center down coil (S2-1 on port SV1).

8.

Install a center rack control boom sense adapter cable (P/N 115-0230-039) on the machine’s down coil.

9.

Connect the coil connector to the installed boom sense adapter cable.

10.

Connect the connectors on the installed boom sense adapter cable to the CENTER DOWN harness 
connectors on the AutoBoom harness cable.

Connect the Harness Cable to the Sensors

1.

Locate the CENTER SENSOR connector on the AutoBoom harness cable.

2.

Connect the CENTER SENSOR connector to the installed center sensor (P/N 063-0130-018).

3.

Locate the LEFT OUTER SENSOR connector on the AutoBoom harness cable.

4.

Connect the LEFT OUTER SENSOR connector to the installed left sensor cable (P/N 115-0230-051).

5.

Locate the RIGHT OUTER SENSOR connector on the AutoBoom harness cable.

6.

Connect the RIGHT OUTER SENSOR connector to the installed right sensor cable.

7.

If optional inside boom sensors are installed, repeat the steps above to connect the sensors.

Connect the Harness Cable to the Controller Cable

1.

Route the harness cable (P/N 115-0230-033) toward the machine’s cab.

Note:

Be sure to allow enough slack in the harness cable for boom racking.

2.

Connect the harness cable to the controller cable (P/N 115-0230-007).

3.

Tighten the connector screw cap to secure the connection.

Connect the Controller (If Applicable)

1.

Route the controller cable (P/N 115-0230-007) into the right side of the machine’s cab.

2.

Locate the two controller connectors and connect them to the AutoBoom controller (P/N 063-0130-021).

Connect the Field Computer (If Applicable)

Refer to the Installation & Operation Manual and the specific wiring schematic beginning on page 48 for 
installation and wiring instructions for the specific field computer being used.

Summary of Contents for AutoBoom SX275































































Reviews:

No comments

Brands by name

Popular brands

Load more brands