background image

8

electrical  connection

ELECTRICAL REQUIREMENTS

•  This appliance must be properly installed and grounded by a qualified technician in 

accordance with the National Electrical Code ANSI/NFPA No.70 (latest edition) and 

local  electrical  code  requirements.  IN  CANADA:  Electrical  installation  must  be  in 

accordance with the current CSA C22.1 Canadian Electrical Codes Part1 and/or local 

codes.

•  This appliance may be connected by means of permanent “Hard Wiring” or “Power 

Supply Cord Kit”. Power supply cord is not supplied, but it is available through your 

local electric supply house.

•  Use  only  3-conductor  or  4-conductor  CSA/UL  listed  range  cord  rated  at  55  amps 

with 250 V minimum and provided with ring terminals. These cords should be pro-

vided with strain relief or conduit connector.

  Warning:

 Frame grounded through neutral lead. If used in,

  - New branch-circuit installations (1996 NEC),
  - Mobile homes,
  - Recreational vehicles, or

- In an area where local codes prohibit grounding through neutral, use a 4 conductor 

cord or conduit.

•  The  range  must  be  connected  to  the  proper  electrical  voltage  and  frequency  as 

specified on the rating plate.

•  The range can be connected directly to the fused disconnect (or circuit breaker box) 

through flexible, armoured or non-metallic sheathed, copper cable (with grounding 

wire). Allow two to three feet of slack in the line so that it can be moved if servicing 

is ever necessary.

ELECTRICAL CONNECTION WITH POWER CORD

Use a 3-wire power supply cord kit rated for 55 amps - 125/250 Volts with closed loop 

terminals and marked for use with ranges. Where local codes do not permit grounding 

through neutral, use a 4-wire power supply cord kit.
The cord or CSA/UL-listed conduit must be secured to the range with the strain relief 

supplied or with a suitable strain relief. The electrical connection is made at the terminal 

block, which is located behind the access door on the back of the range.

ELECTRICAL CONNECTION WITH CONDUIT

Use  3/4”  (1.90  cm)  trade  size  conduit  with  a  conduit  clamp,  10  AWG/600  Volt  cop-

per conductor colored red for line 1 and black for line 2 and 12 AWG/600 Volt copper 

conductor (or 10 AWG/600 Volt copper conductor if grounding through neutral) colored 

white for neutral with closed loop terminals marked for use with ranges.
Where  local  codes  do  not  permit  grounding  through  neutral,  use  a  green  10  AWG 

copper conductor as directed in the 4-wire connector directions. The conduit must be 

secured to the range with the strain relief bracket. The electrical connection is made at 

the terminal block which is located behind the access door on the back of the range.

TO  AVOID  ELECTRICAL  SHOCK 

HAZARD,  BEFORE  INSTALLING  THE   

APPLIANCE,  SWITCH  POWER  OFF  AT 

THE  SERVICE  PANEL  AND  LOCK  THE 

PANEL  TO  PREVENT  THE  POWER 

F R O M   B E I N G   S W I T C H E D   O N  

ACCIDENTALLY.

WARNING

Summary of Contents for VEFSEE 244 P Series

















Reviews: