background image

20304685

VC41LDVI/VC41CDVI Gas Fireplace Insert

7

GeNeRAL INSTALLATION INFORMATION  

BeFORe yOu START

Read this homeowner manual thoroughly and follow all 

instructions  carefully.  Inspect  all  contents  for  shipping 

damage and immediately inform your dealer if any damage 

is found. Do not install any unit with damaged, incomplete, 

or substitute parts. Check your packing list to verify that all 

listed parts have been received.
The following factors should be taken into consideration:

  This insert should have sufficient access for its safe 

operation and maintenance.

  The flow of combustion and ventilation air must not be 

obstructed.

  Minimum clearances to combustibles, such as mantels, 

must be maintained. 

Refer to Pages 8 and 9, Figures 

3, 4 and 5.

  Never obstruct the front opening of the insert.

  Do  not  install  in  the  vicinity  where  gasoline  or  other 

flammable liquids may be stored.

  These  units  can  be  installed  in  a  bedroom.  Refer  to 

National Fuel Gas Code ANSI Z233.1/NFPA 54 (current 

edition),  the  Uniform  Mechanical  Code  (current  edi-

tion), and Local Building Codes for specific installation 

requirements.

IMPORTANT: your direct vent insert was designed to 

be installed in an existing wood burning fireplace. The 

location and clearances are subject to local building 

codes

.

CLeARANCeS
MINIMuM FIRePLACe SIZe/CLeARANCeS 

TO COMBuSTIBLeS

W

ARNING

The dimensions shown on 

Pages 8 and 9, 

Figures 3 and 4

, are minimum clearances to 

maintain when installing this heater. Follow 

these instructions carefully to ensure safe 

installation.  Failure  to  follow  instructions 

exactly can create a fire hazard.

INSeRT APPLICATIONS

Before  installing  the  gas  fireplace  insert,  consider  the 

functioning needs of the fireplace. Confirm the size of the 

fireplace cavity, the design of the chimney, and the avail-

ability of the gas supply and electricity for the insert fan.

IMPORTANT: your  direct  vent  insert  is  designed  to 

be  only  vented  vertically  with  a  minimum  height  of 

10 feet.

When the unit is installed into a wood burning fireplace, 

the minimum distance the mantel can be placed above the 

fireplace is governed by local building codes applicable to 

wood burning fireplaces. Consult local authorities having 

jurisdiction  for  these  clearances. The  underside  of  the 

mantel will become warm. Use only finishes which are heat 

resistant and do not discolor.

Summary of Contents for VC41CDVINTSC

















































Reviews: