background image

Lexington Direct Vent 

Gas Fireplace

with the LexFire Burn System™

Models: LX32DV, LX36DV

 

WARNINGS

IF the INFoRMAtIoN IN theSe INStRuctIoNS 

ARe  Not  FoLLoWeD  eXActLy,  A  FIRe 

oR  eXpLoSIoN  MAy  ReSuLt  cAuSING 

pRopeRty DAMAGe, peRSoNAL INjuRy oR 

LoSS oF LIFe.
–  Do  not  store  or  use  gasoline  or  other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

–  WhAt to Do IF you SMeLL GAS

•   Do not try to light any appliance.

•   Do not touch any electrical switch; do not 

use any phone in your building.

•   Immediately call your gas supplier from 

a  neighbor's  phone.  Follow  the  gas 

supplier's instructions.

•   If you cannot reach your gas supplier, call 

the fire department.

–  Installation and service must be performed 

by  a  qualified  installer,  service  agency  or 

the gas supplier.

WARNING: Improper installation, adjustment, 

alteration, services or maintenance can cause 

injury or property damage. Refer to this manual. 

For  assistance  or  additional  information 

consult a qualified installer, service agency or 

the gas supplier.   
this  appliance  is  only  for  use  with  the  type 

of  gas  indicated  on  the  rating  plate.  this 

appliance is not convertible for use with other 

gases, unless a certified kit is used. 
this appliance may be installed in an aftermarket*, 

permanently  located,  manufactured  home, 

where not prohibited by local codes.

*Aftermarket:  completion  of  sale,  not  for  purpose  of 
resale, from the manufacturer. 

Due  to  hIGh  teMpeRAtuReS,  the 

AppLIANce  ShouLD  Be  LocAteD  out  oF 

tRAFFIc AND AWAy FRoM FuRNItuRe AND 

DRApeRIeS.
chILDReN AND ADuLtS ShouLD Be ALeRteD 

to  the  hAZARDS  oF  hIGh  SuRFAce 

teMpeRAtuRe AND ShouLD StAy AWAy to 

AVoID BuRNS oR cLothING IGNItIoN.
youNG chILDReN ShouLD Be SupeRVISeD 

WheN they ARe IN the SAMe RooM AS the 

AppLIANce.
cLothING oR otheR FLAMMABLe MAteRIAL 

ShouLD Not Be pLAceD oN oR NeAR the 

AppLIANce.
Keep  the  RooM AReA  cLeAR AND  FRee 

FRoM coMBuStIBLe MAteRIALS, GASoLINe, 

AND  otheR  FLAMMABLe  VApoRS  AND 

LIquIDS.

INStALLeR: Leave this manual with the appliance.

coNSuMeR: Retain this manual for future refer-

ence.

510528
LX cover

51D0528  2/13  Rev. 15

Installation and 

Operating Instructions

Summary of Contents for Lexington LX32DV

















































Reviews: