background image

CDVSC7 & CDV7 Series Gas Fireplace

34

69D3011

eleCTRonIC IGnITIon opeRaTInG InSTRuCTIonS

a. 

This  appliance  is  equipped  with  an  ignition  device 

(Piezo) which automatically lights the pilot. Do NOT 

try to light the burner by hand. 

B. 

BEFORE OPERATING smell all around the appliance 

area for gas. Be sure to smell next to the floor because 

some  gas  is  heavier  than  air  and  will  settle  on  the 

floor.

whaT To Do IF you SMell GaS:

 

  Turn off all gas to the appliance.

 

  Open windows. 

 

  Do not attempt to light any appliance.

 

  Do not touch any electric switch; do not use any 

phone in your building.

 

  Immediately  call  your  gas  supplier  from  a 

neighbor's phone. Follow the gas supplier's instructions.

 

  If you cannot reach your gas supplier, call the fire department.

C.  

Turn off all electric power to appliance. 

D.

  Do not use this appliance if any part of it has been under water. Immediately call a qualified 

service technician to inspect the appliance and to replace any part of the control system 

and any gas control that has been under water. 

  lIGhTInG eleCTRonIC IGnITIon   

 FoR youR SaFeTy ReaD BeFoRe lIGhTInG 

  To TuRn oFF GaS   

1. Open lower door.
. Turn RS-OFF_ON rocker switch to “OFF”.
3. Turn off all electric power to the appliance if service is to be performed.
4. Close lower door. 

1. 

STop!

 Read the safety information above.

. Make sure all power to unit is turned off. 
3. Set thermostat to lowest setting.
4. This appliance is equipped with an ignition device which automati-

cally lights the burner. Do not try to light the burner by hand. 

5. Turn on all electric power to appliance.
6. Set thermostat to desired setting.
7. Turn RS-OFF-ON rocker switch to “ON”. 
8. If the appliance will not operate, follow the instruction 

To Turn Off Gas 

below

 

and call your 

service technician or gas supplier. 

LO

HI

FP2102
BDV electronic valve

Electronic Gas Valve 

w

a

R

n

In

G

If  you  do  not  follow  these  instruction 

exactly,  a  fire  or  explosion  may  result 

causing  property  damage,  personal 

injury or loss of life.

w

a

R

n

In

G

never  use  an  open  flame  to  check  for 

gas leak. 

Summary of Contents for CDVR33n





































































Reviews: