Verkada AX11 Install Manual Download Page 7 | Manualshive

Page: 7 / 11

Verkada AX11 Install Manual Download Page 7

Verkada Inc. 405 E 4th Ave, San Mateo, CA, 94401

[email protected]

All specifications are subject to change without notice.

Copyright © Verkada Inc . All rights reserved.

Recommended Wiring

Wiring

Signal

AWG

Twisted Pair

Conductor

Shielded

Max Length

Reader Option 1
(Wiegand or AD31)

22

Yes

Yes

250ft

Reader Option 2
(Wiegand or AD31)

20

Yes

Yes

300ft

Reader Option 3
(Wiegand or AD31)

18

Yes

Yes

500ft

12V Power (22 Gauge)

22

Yes

Yes

600ft

12V Power (18 Gauge)

18

Yes

Yes

1500ft

Inputs

22

Yes

Yes

1000ft

Dry Relay Output

18

Yes

Yes

1500ft

The AX11 card reader interface is capable of supporting Verkada Readers over RS-485 and standard
Wiegand readers. The following table shows the wire types that are recommended for use with AX11.

We recommend using one twisted pair for GND and Vin (power) and one twisted pair for the data (D0/D1 or
A/B).

Wiring methods shall be in accordance with National Electrical Code, ANSI/NFPA 70.

Required Network Settings

With the AX11, you must use shield wiring.

Drain wire of the cable should be secure to the nearest grounding point, indicated with on the controller,
with a conductive M4 screw.

An Ethernet connection with DHCP must be used to connect the AX11 to the Local Area Network (LAN).
You also need to configure firewall settings to communicate with the AX11.
• TCP port 443
• UDP port 123 (NTP time synchronization)

Shield Wiring and Grounding

«
...
5
6
7
8
9
...
»

Summary of Contents for AX11












Reviews:

No comments