Verkada AX11 Install Manual Download Page 2 | Manualshive

Page: 2 / 11

Verkada AX11 Install Manual Download Page 2

Verkada Inc. 405 E 4th Ave, San Mateo, CA, 94401

[email protected]

All specifications are subject to change without notice.

Copyright © Verkada Inc . All rights reserved.

Introduction

Document revision

Firmware

Levels of Access Control

V1.0

Firmware version can be verified and upgraded in the
Command dashboard at command.verkada.com.

• Attack Level/Grade: Level I

• Endurance Level/Grade: Level I

• Line Security Level/Grade: Level I

• Standby Power Level/Grade: Level I

Note

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

This equipment is for use in a restricted access area.

Ensure power is disconnected from the AX11 before servicing the product or connecting/disconnecting
peripherals.

Warning

Document Details

«
1
2
3
4
...
»

Summary of Contents for AX11












Reviews:

No comments