Verine Marcello NBFP00RN Installation, User And Servicing Instructions Download Page 12

 

12 

U

SERS 

G

UIDE

 

Useful tips & recommendations 

 

Once  your  fire  has  been  fitted,  the  following  recommendations  are  made  to 
ensure you enjoy the best results from your purchase; 

1

 

The  installation  of  this  appliance  must  have  been  carried  out  by  a  qualified 
installer  and  in  accordance  with  the  requirements  of  the 

Gas  Safety 

(Installation & Use) Regulations

 

2

 

The  glass  door  and  the  upper  part  of  the  fascia  panel  are  considered  to  be 
working  surfaces  and  as  such  will  become  hot  when  in  use.

 

Care  should  be 

exercised  when  using  the  controls  of  the  appliance  when  it  is  hot.    We  also 
recommend  that  a  fireguard,  conforming  to  BS  6539  or  BS  6778,  be  fitted  for 
the protection of young children, the elderly or infirm. 

3

 

When  new,  any  painted  surfaces  or  ceramic  components  may  produce  a  slight 
odour, but this will completely vanish after a few hours of use.  

The  appliance

  MUST  NOT

  be  used  with  the  front  fascia  panel  in  the  dropped 

down  position  or  with  the  glass  panel  removed.  If  there  is  any  suspicion  of 
damage to the glass the appliance must not be used. 

 

To  obtain  the  best  results  from  your  fire  we  recommend  that  it  be  serviced 
annually. 

These  instructions  are  provided  to  assist  you  to  operate  the  fire  correctly  and 
should be kept in a safe place. 

If  you  have  any  reason  to  suspect  a  gas  leak,  turn  off  the  appliance  at  the 
isolating point and contact your installer. 

Curtains should not be hung above the appliance. 

Operation of the fire 

1

 

The  pilot  flame  heats  the  thermocouple  probe  and  allows  gas  to  flow  to  the 
burners.    If  due  to  pilot  failure,  the  thermocouple  cools,  no  gas  will  flow  to  the 
main burner.  If the fire is turned off or the flames go out, wait for 

AT LEAST 3 

MINUTES

 before attempting to relight the fire. 

2

 

For  convenience  you  will  find  with  the  appliance  a  card  giving  concise  lighting 
instructions, please keep this in a safe place.  

Opening and Closing the Fascia Panel 

CAUTION:  ONLY DO THIS WHEN THE FIRE IS COLD 

To  open  the  fascia  panel  grip  it  at  each  side,  lift  slightly,  pull  outwards  and 
lower. 

This will allow access to the gas control  and to the battery pack-signal receiver 
to light the appliance and change the batteries. 

To  close  the  fascia  grip  it  at  each  side,  lift  fully,  push  forwards  and  release. 
Always grip the fascia at each side where it will be cool and not at the top where 
it may be very hot. 

Summary of Contents for Marcello NBFP00RN




















Reviews: