background image

UX 410 I

NSTALLATION

 G

UIDE

31

A

PPENDIX

 A

Caution and Warning Messages

UX 410 Caution

and Warning

Messages

Products with UL/cUL Listed should include French translations of Caution and 
Warning notices. The following table shows all notices found in the document, 
their location and the equivalent French translations.

Table 3

Caution and Warning Messages

Notice

Chapter

Page

English Text

French Text

Caution

Setup

page 

9

Avoid placing metallic objects at 
the front and around the card 
reader.

Évitez de placer des objets métalliques à 
l'avant et autour du lecteur de carte.

Warning

Setup

page 

9

For safety, do not string cables or 
cords from your installation cabinet 
or housing across a walkway.

Pour la sécurité, ne sont pas des câbles à 
cordes ou des cordons de votre armoire 
d'installation ou de logement à travers 
une passerelle.

Caution

Setup

page 

10

Remove any protective plastic over 
the front of the Antenna unit before 
use, or the unit may not work 
properly.

Retirez tout plastique de protection sur le 
devant de l'unité d'antenne avant 
l'utilisation, ou l'appareil peut ne pas 
fonctionner correctement.

Warning

Setup

page 

10

Do not use a unit that has been 
damaged.

If a label or component appears 
damaged, please notify the 
shipping company and your 
Verifone service provider 
immediately.

Ne pas utiliser un appareil qui a été 
endommagé.

Si une étiquette ou d'un composant 
semble endommagé, se il vous plaît 
aviser la compagnie de navigation et 
votre fournisseur de services Verifone 
immédiatement.

Caution

Setup

page 

13

Make sure the installation method 
does not invalidate the Anti-
Removal Switch (ARS) function. 
Do not, for instance, install the 
Controller Unit in a sub-chassis 
that can be removed from the main 
cabinet.

Assurez-vous que la méthode 
d'installation ne remet pas le 
commutateur anti- enlèvement fonction 
(ARS). Ne pas, par exemple, d'installer 
l'unité de commande dans un sous- 
châssis qui peut être retirée du boîtier 
principal.

Caution

Setup

page 

13

For optimal installation, the 
thickness of the mounting frame 
should be approximately 2 mm.

Pour une installation optimale, l'épaisseur 
du panneau d'installation doit être 
d'environ 2 mm.

Caution

Setup

page 

14

Avoid placing metallic objects at 
the front and around the card 
reader.

Évitez de placer des objets métalliques à 
l'avant et autour du lecteur de carte.

Summary of Contents for UX410




































Reviews: