Verhagen Leiden V-move 650 User Manual Download Page 16

Verhagen Leiden B.V. 

|

  Hoge Rijndijk 267 

|

 2314 AG Leiden 

|

 T: +31 (0)71 581 30 30 

|

 F: +31(0)71 541 61 89

 

 

 

 

 

 

15 

 

[email protected] 

|

 www.verhagenleiden.nl

 

 

7.4 

Battery life 

Batteries  can  wear  quickly  if  they  are  not  used  correctly.  Fast  wear  falls  outside  the 
guarantee. 
 

Tips for a long battery life: 

1.  It is recommended to never drive the battery fully flat. Further charging a nearly full battery is 

also advised against. 

2.  Immediate charging of an empty battery considerably lengthens the working life. Discharging 

more than 20% affects the working life. 

3.  Never interrupt charging and allow the battery to fully charge. 
4.  If  the  V-move  650  is  put  out  of  use  (for  a  longer  time),  it  is  advisable  to  keep  the  battery 

charger connected. This automatically keeps the battery charged. 

5.  If  the  batteries  are  too  heavily  loaded  this  will  greatly  shorten  the  working  life.  It  is  then 

necessary to adapt the load.  

6.  It is advisable to not fully discharge the batteries. If this happens too often, faster wear will be 

the  result.  Keep  a  close  eye  on  the  battery  condition  meter.  Connect  the  battery  charger  in 
good time.  

7.  The batteries must be charged with the correct charger and for a certain time. If the charging 

current is too low or the duration of charging is too short, the batteries will not be fully charged 
and  the  capacity  of  the  batteries  will  be  too  low  for  your  application,  with  faster  wear  as  a 
consequence.  If  the  charging  current  is  too  high  or  the  duration  of  charging  is  too  long,  the 
battery  will  become  overloaded. The  plates  in your battery will then become overheated and 
can be damaged. 

8.  If the batteries are only e.g. 60% empty and connected to the charger again, the batteries will 

not  have  time  to  rest.  The  temperature  of  the  batteries  will  rise  with  faster  wear  as  a 
consequence.  The  battery  voltage  will  also  be  higher  than  the  actual  energy  state  so  a 
discharge limiter will no longer correctly work. 

9.  The  temperature  of  the  battery  may  not  become  too  high.  This  makes  the  acid  more 

aggressive. Working with and charging in a cool space lengthens the working life.  

10. If  the  batteries  are  used  on  more  than  3  days  a  week  they  will  wear  more  quickly.  When 

choosing the batteries it is important to take account of the frequency of use. 

11. A  battery  gradually  empties  by  self-discharging. If a battery remains in a discharged state, it 

will sulphate and can be irreparably damaged. We therefore recommend recharging a stored 
V-move  650  at  least  every  3  months.  It is also possible to keep the charger  connected. The 
batteries are then kept charged with a trickle function. 

 
When  replacing  the  battery,  the  old  battery  must  be  disposed  of  according  to  the  locally  applicable 
regulations. 

Summary of Contents for V-move 650


















Reviews: