VERDER VA 50 Instructions-Parts List Manual Download

Page: 10 / 36

819.4496

Installation

Flange Connections

The fluid inlet and outlet ports are 2 in. raised face, standard
150 lb class pipe flanges. Connect 2 in. flanged plastic pipe
to the pump as follows. You will need:

•

torque wrench

•

adjustable wrench

•

a 6 in. diameter, 1/8 in. thick PTFE gasket, with four 0.75 in.
diameter holes on a 4.75 in. diameter bolt circle, and a

2.20 in. diameter center

•

four 5/8 in. x 3 in. bolts

•

four 5/8 in. spring lockwashers

•

eight 5/8 in. flat washers

•

four 5/8 in. nuts.

Place a flat washer (E) on each bolt (C). Refer to F

. 3.

Align the holes in the gasket (B) and the pipe flange (A)
with the holes in the pump outlet flange (S).

Lubricate the threads of the four bolts. Install the bolts
through the holes and secure with the washers (E),
lockwashers (D), and nuts (F).

Hold the nuts with a wrench. Refer to the tightening
sequence in F

. 3 and torque the bolts to 27–41 N•m.

Do not over-torque.

Repeat for the pump inlet flange (R).

BOLT TIGHTENING SEQUENCE

. 3

_______________________________________________________________________

04405

04615B

KEY

Flanged Plastic Pipe

PTFE Gasket

Bolt

Lockwasher

Flat Washer

Nut

2 in. Fluid Inlet Flange

2 in. Fluid Outlet Flange

Lubricate threads. Torque to 27–41 N•m. Do
not over-torque.

Summary of Contents for VA 50





































Search results

Summary of Contents for VA 50

Reviews:

Related manuals for VA 50

Brands by name

Popular brands

VERDER VA 50, Instructions-Parts List Manual

Search results

Summary of Contents for VA 50

Reviews:

Related manuals for VA 50

Brands by name

Popular brands