VERDER JEC JRZP Series Operating & Maintenance Manual Download

Page: 9 / 59

MAINTENANCE

ROTOR CASE DISASSEMBLY

Prior to removal of pump, the shut-off valves in the suction and discharge pipe work must be closed.

If there is any risk that product may be hardened, crystallized or frozen in the pump, it should be

thoroughly drained and cleaned immediately after use. Similar attention must be applied to the seal

flushing system. Remove power before servicing to prevent from any unintended start of the pump

by authorized electrician.

Remove Front cover and O-ring after removing the four cap

nuts from the front cover. If it is stuck, tap on the front cover

with a soft mallet and pull out.

If the front cover was stuck at dowels, insert flat driver at the

two groove of between front cover and rotor case to be

separated.

Place the plastic round bar between the rotors and remove

rotor bolts with the rotor bolt extraction tool. To avoid damage

rotor bolt, the extraction tool should be position in the groove

properly and pushed by left hand strongly.

Turn the first rotor bolt as counter-clockwise and remove both

of rotor bolts.

The rotors can be removed from the pump case by pulling

straight.

If it is stuck tight, alternately tap on the back of the inlet and

outlet ports with soft mallet after removing the four hex nuts of

stud bolts securing the case to the gearbox.

Treat carefully the rotors to avoid damage.

Remove rotating seal rings from the backside of the rotors as

shown in Figure 4. Then, O-ring for rotors can be removed.

Fig. 1

Fig.2

Figure 1

Fig. 3

Fig. 4

Summary of Contents for JEC JRZP Series




























































Search results

Summary of Contents for JEC JRZP Series

Reviews:

Related manuals for JEC JRZP Series

Brands by name

Popular brands

VERDER JEC JRZP Series, Operating & Maintenance Manual

Search results

Summary of Contents for JEC JRZP Series

Reviews:

Related manuals for JEC JRZP Series

Brands by name

Popular brands