VERDER JEC JRZP Series Operating & Maintenance Manual Download

Page: 14 / 59

Double Mechanical Seal Maintenance

Remove the Seal ring from the rotor case & rotor (shown in Figure

19) and inspect them. If any seal is damaged, do not re-use and

replace it.

Clean both shaft ends and the rotor case before assembling. Push

the replacing NEW Seal ring into the rotor case O-ring and turn fit

into the seal pins on the seal body after Rotor Case Assembly on

page 15.

In order to replace the product side of mechanical seal, refer to Figure 16~18.

While, in order to replace the flushing side of mechanical seal, refer to Figure 20~22.

After rotor case removed (‘Page 9 & 10’), pull out and remove the

Double seal rotating part from the shaft and inspect them.

If any Double seal rotating part, Seal face and O-ring is damaged,

do not re-use and replace it.

Clean both shaft ends and the rotor case before assembling.

Lubricate the replacing NEW Double seal rotating part O-ring and

install it in the Double seal rotating part. Slide and insert the
Double seal rotating part on the shaft making sure to line the slot

on the Double seal rotating part to the pin in the shaft.

Place the rotor case face down on the table and pull out carefully

the Double seal ring (53) out of rotor case by hands shown in

Figure 21. Carefully treat Double seal ring (53) because carbon is

fragile material.

Lubricate the replacing double seal ring or O-ring and insert it

into the rotor case and fit into the Seal pin properly.

After remove Double seal ring (53), check whether wave spring

(61) has been damaged or not. If wave springs (61) were

damaged, replace it as shown Figure 22.

See ‘Rotor Case Assembly’ on ‘Page 15’ to continue.

Fig. 22

Fig. 19

Fig. 20

Fig. 21

Summary of Contents for JEC JRZP Series




























































Search results

Summary of Contents for JEC JRZP Series

Reviews:

Related manuals for JEC JRZP Series

Brands by name

Popular brands

VERDER JEC JRZP Series, Operating & Maintenance Manual

Search results

Summary of Contents for JEC JRZP Series

Reviews:

Related manuals for JEC JRZP Series

Brands by name

Popular brands