•
2!Ŗ"+
moon
Ŗ
flower
• Built-in automated
-11"/,0
4&1%01/*",!
variable speed
*,1/*)
•
ound activated programs
4&1%3/&)"0",0&1&3&16
•
11& //,$"+",1#*/" %&,!&3&!2)"+
*1"
"1/"+ ," *,1/*))"!"&1%"/#/*+1%"-%60& )/"/Ŗ-,") *,1/*)0*/#/*+1%"&, )2!"!
/"+*1"Ķ
When
"1/"+
powers up, it defaults to running the program set by the rear panel
controls
Ķ%"#&/01 *,1/*)!'201+",1!"1"/+&,"01%" *,1/*)+01"/Ķ */"5+-)"ķ%"#&/01
!'201+",1&0!*,"*,1%"/"/-,")ķ1%"/"/-,")4&)) 10+01"/,!/"+*1"#2, 1&*,0
4&))")&+&1"!Ķ#1%"#&/01 *,1/*)!'201+",1&0!*,"#/*+1%"/"+*1"ķ1%"/"+*1"4&)) 10
+01"/,!/"/Ŗ-,") *,1/*)04&))")&+&1"!Ķ#,&,&1&)!'201+",1&0+!"#/*+1%"/"/Ŗ-,")
*,1/*)0,!6*24&0%1*20"1%"/"+*1"ķ6*24&))#&/01,""!1*-*4"/ 6 )"1%"2,&1&,*/!"/1*
$&3"1%"/"+*1" "001*)) *,1/*)#"12/"0Ķ#6*2+(",&,&1&)!'201+",1#/*+1%"
/"+*1",!1%",4&0%1*20"1%"/"/Ŗ-,") *,1/*)0ķ6*24&)),""!1*#&/01-*4"/ 6 )"1%"2,&1&,
*/!"/1*/"&,&1&)&7"1%"
/"/Ŗ-,") *,1/*)0Ķ
For added convenience when operating without a
remote, Tetra Beam will automatically power up after a few seconds of being plugged in.
"/
Panel
"12/"0,!*,1/*)0
STROBE
MODE
ON
OFF
AUTO
SOUND
AUDIO SENSITIVITY
LOW
HIGH
SPEED
LOW
MIC
HIGH
FUSE
POWER IN
TETRA BEAM
1
2
3
4
5
6
7
8
1.
STROBE S
WITCH
:
Turns the strobe effect on or off
2.
AUDIO SENSITIVITY
CONTROL:
Sets the sound threshold for sound-activated pattern changes when the
MODE switch (#5) is set to the SOUND position. Turn counter-clockwise to decrease sensitivity and clockwise
to increase sensitivity
3.
MIC:
Internal microphone for the sound-activated pattern changes
4.
SPEED CONTROL:
Controls the speed of the pattern changes when the MODE switch (#5) is set to the AUTO
position
5.
MODE
SWITCH
:
Controls how patterns are changed. In the AUTO position, patterns cycle automatically at a
rate controlled by the SPEED control (#4). In the SOUND position, patterns change based on input from th MIC
(#3) and the threshold set by the AUDIO SENSITIVITY control (#2)
6.
POWER IN:
Tetra Beam is equipped with a fixed power cable and will power up automatically when
plugged in. Review the safety section (page 5) before connecting the end of this cable to a standard AC power
outlet.
7.
FUSE:
As a protective measure, Tetra Beam is equipped with a F1AL250V safety fuse. In the case of a mains
power surge, the fuse will blow and protect the internal electronics. To access the fuse, unplug the power
cable from the AC outlet and use a phillips-head screwdriver to open the fuse holder.
8.
SAFETY LOOP
- When using Tetra Beam in a hanging application a safety chain or cable must be connected
to this loop
Č