Venue Lighting Effects revolver laser Manual Download Page 3

3

www.venuelightingeffects.com

INTRODUCTION

The Venue Revolver Laser is a DMX intelligent, dual sided, moving head effect 
light, which includes both a laser and moonflower effect. It is lightweight and 
compact which makes it a great light for mobile DJs, clubs and parties. This unit 
can be used as a standalone fixture in sound-activated mode, or controlled via 
DMX controller.

TABLE OF CONTENTS

BEFORE YOU BEGIN

  

4

What is included  

4

Unpacking Instructions  

4

Manual Conventions  

4

Icons  

4

SAFETY INSTRUCTIONS

  

5

INTRODUCTIONS

  

6

Control Features  

6

Additional Features  

6

Control Panel  

6

SETUP

  

7

AC Power   

7

Back Panel   

7

Mounting Orientation  

8

Rigging  

8

Signal Linking  

9

OPERATING INSTRUCTIONS

  

9

Control Panel Buttons  

9

Menu Map  

10

STANDALONE OPERATION

  

12

Automatic  

12

Sound-active  

13

Audio sensitivity  

13

Custom static colors/
Manual Control  

13

DMX OPERATION

  

13

Configuring the Starting Address  

14

Master/Slave 
(Standalone Operating Modes)   

14

11-Ch mode DMX operation  

15

17-Ch mode DMX operation  

15

17-Ch mode DMX operation  

15

DMX Parameters  

16

APPENDIX 

 

18

DMX Primer  

18

General Troubleshooting  

18

Fixture Linking  

19

DMX Data Cable  

19

Cable Connectors  

19

3-Pin to 5-pin Conversion Chart  

20

Setting Up a DMX Serial Data Link  

20

General Maintenance  

20

TECHNICAL SPECIFICATIONS 

 

21

WARRANTY 

 

22

Summary of Contents for revolver laser

























Reviews: