background image

3

www.ventilation-system.com

• 

Read the user’s manual carefully prior to installing and operating the unit.

• 

Fulfil the user’s manual requirements as well as the provisions of all the applicable local and national 

construction, electrical and technical norms and standards.

• 

The warnings contained in the user’s manual must be considered most seriously since they contain 

vital personal safety information.

• 

Failure to follow the rules and safety precautions noted in this user’s manual may result in an injury 

or unit damage.

• 

After a careful reading of the manual, keep it for the entire service life of the unit.

• 

While transferring the unit control the user’s manual must be turned over to the receiving operator. 

Symbol legend:

UNIT MOUNTING SAFETY PRECAUTIONS

WARNING!

RESTRICTED!

Disconnect the unit from power 

mains prior to any installation and 

repair operations.

The unit must be grounded!

Do not operate the unit outside 

the temperature range stated in 

the user's manual. Do not operate 

the unit in aggressive or explosive 

environments.

Do not use damaged equipment 

or cables when connecting the 

unit to power mains.

While installing the unit follow 

the safety regulations specific to 

the use of electric tools.

Unpack the unit with care. 

Do not change the power cable 

length at your own discretion. Do 

not bend the power cable. Avoid 

damaging the power cable.

Do not lay the power cable of 

the unit in close proximity to 

heating equipment.

SAFETY REQUIREMENTS

V51EN-04.indd   3

23.10.2015   9:57:22

Summary of Contents for KSB 100





















Reviews: