background image

www.vents-us.com

5

TwinFresh Comfo RA(1)-50(-2)

The unit is designed to ensure continuous mechanical air exchange in houses, offices, hotels, cafes, conference halls and other utility and public spaces.
The ventilator is equipped with a ceramic regenerator that enables supply of fresh filtered air heated by means of extract air heat energy regeneration. 
The ventilator is designed for through-the-wall mounting. 
The telescopic ventilator design enables its installation in the walls with various thickness, see the table below: 

Model 

Wall thickness 

RA-50 

RA1-50

240 mm - 425 mm (9  

7

/

16

’’ - 16  

9

/

16

”)

RA-50-2 

RA1-50-2

120 mm - 300 mm (4  

3

/

4

’’ - 11  

13

/

16

’’)

The unit is rated for continuous operation.
Transported air must not contain any flammable or explosive mixtures, evaporation of chemicals, sticky substances, fibrous materials, coarse dust, soot 

and oil particles or environments favourable for the formation of hazardous substances (toxic substances, dust, pathogenic germs).

PURPOSE 

THE UNIT MAY NOT BE OPERATED BY CHILDREN OR PERSONS WITH REDUCED 

PHYSICAL, MENTAL OR SENSORY CAPACITIES, OR LACKING THE APPROPRIATE 

TRAINING. 

THE UNIT MUST BE INSTALLED AND CONNECTED ONLY BY PROPERLY QUALIFIED 

PERSONNEL AFTER THE APPROPRIATE BRIEFING. 

THE CHOICE OF UNIT INSTALLATION LOCATION MUST PREVENT UNAUTHORIZED 

ACCESS BY UNATTENDED CHILDREN.

DELIVERY SET

Name 

Quantity 

Ventilator 

1 item 

Mounting kit 

1 item

Cardboard template

1 item

Remote control 

1 item

Mounting hood installation instruction 

1 item

User's manual for the ventilator 

1 item

Packing box 

1 item

DESIGNATION KEY

TwinFresh Comfo R A 1 - 50 - 2

Ventilation hood model 

_  — EH white 160

2 — EH-2 grey 160

Rated air capacity [m

3

/h] 

Front panel modification

1 — flat front panel 
Automation availability  

A — automation type 
Air duct cross section 

R — round 
Ventilator series 

Summary of Contents for RA1-50-2





















Reviews: