background image

2

一、

1. This  product  is  a  Home  Use  Treadmill.  Heart  rate  sensor  does  not  belong  to  the

medical equipment, just for your reference.

2. When using this Treadmill, in its rear should be vacated 2m*1m as security zone, and

should not place any stuff within security zone.

3. The Treadmill is suitable to place indoor of avoiding damp, does not allow to splash

water or place any stuff on it.

4. When  running  the  Treadmill,  DC  Motor  may  bring  spark,  should  be  kept  away  from

Inflammable and explosive materials.

5. In use, should ensure the Treadmill to put on plat ground, if not, to adjust the mat below

or using carpet、rubber sheet to make it smooth.

6. The voltage is 220V-240V, exceed the range of voltage, may it doesn’t’t work properly.

The power  has to  match  the  power  line  and  single-phase,  three-hole well-grounded
socket during using, the same power line avoid using other appliance.

7. Before using this Treadmill, please do 10 minutes of warm-up exercises, should wear

sweat suit、sports shoes and socks.

8. Do  not  stand  on  running  belt  when  testing,  and  do  not  allow  two  or  more  than  two

person using the Treadmill at the same time.

9. Should be cautious when up and down; before starting, have to hold the handle, put

two feet on both sides of decorative strips; Speed should from low up to high when
running; When leave the Treadmill, first to make the speed to the minimum in order to
avoid hurt that loss balance.

10. Safety  Key  have  to  clip  cloths  when  running,  if  need  to  stop  can  pull-off  switch,  the

Treadmill will stop running to achieve security purposes. After using, unplug the power
plugs that ensure safety.

11. Need to have adult supervision if children use or near the Treadmill. Patients with heart

disease should not use the machine alone. Physical discomfort under the guidance of a
doctor to use.

12. The Treadmill should avoid solar、raining and moist. Should use cleaning rag to clean

machine in order to avoid the accumulation of dust.

13. Do not stand on Treadmill or placing stuff when not using.
14. Should avoid overload operation for a long time, it may cause damage of Motor and

Controller; Accelerated aging bearing and running belt.

15. When moving the Treadmill, first to fold the bottom frame. After locked, to hold the end

of bottom frame, then carefully move.

16. The  treadmill  designed  for  Home  Use  only,  please  do  not  used  for  organization  or

commercial.

Attentions

Summary of Contents for CF-2104















Reviews: