Velodyne MiniVee User Manual Download Page 8

Pr epare for Ins tallation

2

.

w w w . v e l o d y n e . c o m

MiniVee User’s Manual

Your new Velodyne subwoofer provides for a number of installation options. Read all the
installation information below in order to determine which installation option is best suited for
your system. 

Remember to perform all installation procedures with system power turned

off to prevent possible damage.

P L A C E M E N T

True subwoofers operate at extremely low frequencies which are primarily omni-directional.
While it is recommended that the subwoofer be placed on the same plane as the satellite
speakers, room and system conditions often dictate otherwise. Keep in mind that frequency
response and output level can be drastically influenced by placement, depending on the acoustic
properties of the listening room. Typically, the optimum location for a subwoofer is tucked away
in a corner of your listening room. This location will usually offer the greatest output levels and
optimum low frequency extension. The worst location for a subwoofer is typically far away from
any walls and close to the center of your room. Avoid these locations when possible.  When
using a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer by the
satellite of the same channel.

Caution!  This subwoofer has electronics built into the cabinet.  Do not place the cabinet
next to sources of heat such as furnace registers, radiators, etc.  Do not place the unit
near sources of excessive moisture, such as evaporative coolers, humidifiers, etc.  The
power cord should be routed in such a way that it will not be walked on, pinched or
compressed in any way that could result in damaging the insulation or wire.

Regardless of where you install your Velodyne subwoofer, it must remain in an upright position
(woofer facing forward). Using, shipping or storing the subwoofer in any other position for an
extended period of time may result in damage to the unit not covered by warranty.

Your new Velodyne subwoofer, like any good speaker system, requires proper positioning within the
listening space to provide maximum performance. Improperly placed speakers may degrade the
sound quality and reduce your listening pleasure. Depending on the size and type of furnishings in
the room, perfect placement may not be possible. Finding the best location within your
environment will likely require some experimentation. We suggest you experiment with the location
during setup to find what sounds best to you when seated in your typical listening position.

Summary of Contents for MiniVee





















Reviews: