background image

10 

 

Move the markers 

• Place the mouse pointer over a dashed marker line. 
• Press and hold the left mouse button. 
• The marker line turns solid. 
• Drag the marker to the appropriate position. 
 
 

Add comment text on the signal screen 

 
For explanation and documentation, each measurement can be supplied with a comment text.   
  
This text will be saved together with the waveform data to the disk file.   
  

To enter the text:   

  
 1.

 

Right click on the screen.  

 

 

 2.

 

Text box will open, to write your comment.  

 

 

 3.

 

Click 

Add Text on Screen

 or 

Remove

 to remove previously inserted text.  

 

 

 4.

 

Right click on the screen to position your text.  

 

 

 5.

 

Click 

Close

.  

 

 

  
You may also click the 

Get Waveform Parameters

 button.   

When this button is pressed the text edit window is cleared and the selected waveform parameters data 
replaces the text.   
  

Tip:

 You can use Ctrl+A, Ctrl+C and Ctrl+V shortcuts in the text edit window.   

  
To make the text transparent with the background, check 

Transparent text.

   

The text will have the same color as the vertical time/frequency markers. 
 
 

Troubleshooting   

 

No signal on the oscilloscope display    

 · No communication with the computer (check that the cable is connected to the USB port)     
 · If USB cable is connected, close the program. Disconnect and reconnect the USB cable and run the 
program again.    
 · RUN button is not ON.   
 · TIME/DIV switch is in the wrong setting.   
 · TRIGGER is ON, set TRIGGER OFF   
 · Y position is wrongly adjusted.   
 · Input amplitude is too large, adjust VOLTS/DIV setting.    
  
If the above tips have no effect, then test on a different computer or different USB port.   
Note. Close the program before disconnecting the USB cable. 

Summary of Contents for PCSU01











Reviews: