![background image](http://html1.mh-extra.com/html/velleman/ham982k/ham982k_user-manual_4108144009.webp)
HAM982K_v2
VELLEMAN
9
b. Edit the Master Code (location 01)
1. Enter '01' (the location of the master code)
2. Enter the new master code (minimum 2 and maximum 5 digits)
3. Validate the new master code with '#' – the previous code will be erased.
c. Setting User Codes (location 11-18)
1. Enter the location of the user code: 11 (user 1), 12 (user 2), 13 (3), 14 (4), 15 (5), 16 (6), 17 (7), 18 (user 8).
2. Enter the new user code (minimum 2 and maximum 5 digits)
Usually one user code is required to arm/disarm the system. User codes 2 to 8 are optional.
3. Validate the new user code with '#' – the previous code for that location will be erased.
To invalid a code, enter the location number and press '#' immediately to erase the existing code.
d. Configuring the protection zones (location 21-28)
1. Enter the location of the zone: 21 (zone 1), 22 (zone 2), 23 (3), 24 (4), 25 (5), 26 (6), 27 (7), 28 (zone 8).
2. Enter code 1: triggering mode:
0= single trigger: the zone can only give alarm once until the system and thus the zone is reset.
1= multiple trigger (default for all zones): the zone can be re-triggered after an alarm if it is still armed.
3. Enter code 2: response delay mode:
0= instant: there is no entry delay ; the alarm is triggered instantly (default zones 3, 4, 5, 6).
1= entry delay 1: there is an entry delay according to the time set on the entry delay timer 1 (default zones 1, 2).
2= entry delay 2: there is an entry delay according to the time set on the entry delay timer 2.
3= 24h-instant: the zone ALWAYS gives alarm when triggered, armed or not (default zones 7, 8).
4. Enter code 3: response time: 0=25ms, 1=250ms, 3=500ms (default for all channels), 4=750ms.
5. Validate the new configuration with '#' – the previous configuration will be erased.
e. Setting the Exit Delay Time / Beep (location 30)
1. Enter the location: '30'.
2. Enter code 1: exit beep: the system beeps during the exit delay period:
'0'= disabled / '1'= enabled (default).
3. Enter the exit delay: 2-999 seconds (default = 60s)
4. Validate the new setting with '#'.
f. Setting the Entry Delay Time / Beep (location 31-32)
1. Enter the location: '31' (entry delay 1) or '32' (entry delay 2).
2. Enter code 1: entry beep: the system beeps during the entry delay period:
'0'= disabled / '1'= enabled (default).
3. Enter the entry delay: 2-999 seconds (default entry delay 1 = 30s ; entry delay 2 = 60s)
4. Validate the new setting with '#'.
g. Setting the Siren Duration (location 33)
1. Enter the location: '33'.
2. Enter code 1: the system will activate its timing alarm output (terminal 9) to generate short signals when the
system is armed (2 signals) or disarmed (1 signal): '0'= disabled (default) / '1'= enabled.
3. Enter the siren time: 2-999 seconds (default = 300s)
4. Validate the new setting with '#'.
Summary of Contents for HAM982K
Page 2: ...HAM982K_v2 VELLEMAN 2...