manualshive.com logo in svg

Velleman DVM98, Manual

Share
Download
Velleman DVM98 Manual Download Page 4

2.1 Function and Range Selector 

 
There are totally 10 functions and 32 ranges provided. A rotary switch is used to 
select functions as well as ranges. 
 

2.2 Power Switch 

 
A push - push switch is used to turn the meter on or off. To extend the battery 
life,  Auto  Power-Off  function  is  provided.  The  meter  will  be  turned  off 
automatically  within  around  40  minutes.  To  turn  on  the  meter  again,  push  the 
power switch to release it and then push it once more. 
 

2.3 Data-Hold Switch 

 
When  this  switch  is  active,  the  meter  will  hold  the  last  display  reading  until 
pushing the switch to release it. 
 

2.4 Input Jacks 

 
This meter has four input jacks that are protected against overload to the limits 
shown. 
During  use  connect  the  black  test  lead  to  COM  jack  and  connect  red  test  lead 
depending on the function selected. 
 

FUNCTION 

RED LEAD 

CONNECTION 

INPUT LIMITS 

 

200mV   

V 

Ω

 Hz 

250V DC or rms AC 

V   & V   

V 

Ω

 Hz 

1000V DC, 700V AC (sine) 

Hz 

V 

Ω

 Hz 

250V DC or rms AC 

Ω

 

V 

Ω

 Hz 

250V DC or rms AC 

 

V 

Ω

 Hz 

250V DC or rms AC 

mA   & mA   

mA 

200mA DC or rms AC       

20A   & 20A   

A  

10A DC or rms AC continuous 
20A for 15 seconds maximum 

 

Summary of Contents for DVM98












Reviews:

No comments

Brands by name

Popular brands

Load more brands