background image

7

2 Product description

FIBERTRAC 32 • Four-wire 4 … 20 mA/HART

62071-EN-211203

Shielding: Provide good shielding between the source and your-

self as well as all other persons. Special source containers (e.g. 

VEGASOURCE) as well as all materials with high density (e.g. lead, 

iron, concrete, etc.) provide effective shielding. 

Time

: Stay as short a time as possible in radiation exposed areas. 

Distance: Your distance to the source should be as large as possible. 

The local dose rate of the radiation decreases in proportion to the 

square of the distance to the radiation source. 

The plant operator must appoint a radiation safety officer with the 

necessary expert knowledge. He is responsible for ensuring that the 

radiation protection ordinance is complied with and for implementing 

all radiation protection measures.

Control areas are areas in which the local dose rate exceeds a certain 

value. Only persons who undergo official dose monitoring are allowed 

into these control areas. You can find the respectively valid limit values 

for control areas in the guideline of the respective authority (in Ger-

many, for example, the radiation protection ordinance).

We are at your disposal for further information concerning radiation 

protection and regulations in other countries.

Radiation safety officer

Control area

Summary of Contents for FIBERTRAC 32





























Reviews: