background image

 

Vega M200, M210, M300, M310 / User Manual 

8

 

Revision № 03 of 05.08.2022 

 

Make a call or send an SMS-message to the SIM-card number of the device within 5 
minutes

 

Otherwise, the inactivated device switches to emergency mode in 5 minutes and starts flashing every 

8 seconds. In this case, repeat activation procedure starting from step 2. 

STEP 4 

After an incoming call or an SMS, the device automatically identifies the phone number and sends an 

SMS-message with the current device settings. The description of the parameters you can see in the chapter 
"Settings". 

Then the device turns on the GPS / GLONASS receiver and switches to the satellite search mode to 

identify its own location. The indicator is flashing every 3 seconds. 

 

 

To search satellites and identify the coordinates, it is recommended to place the device 
in a place where the sky is clearly seen, e. g. if the device is activated in a room, bring it 
to the window 

 
Every time the device identifies its coordinates, it also identifies the current time and adjusts its internal 

clock through satellites. Time setting takes the time zone into account, which is set by the parameter "P". The 
default parameter is 03, which means +3 hours to GMT. 

STEP 5 

After identifying the coordinates, the device registers again in the network and sends an SMS-message 

with the coordinates of the device. After sending the coordinates, the device switches to standby mode, 
waiting for SMS-messages with settings or commands from the user. The device stays 5 minutes in this mode 
and then switches to sleep mode and operates in the "BACKGROUND" mode. While waiting for SMS with 
settings and commands, the indicator is flashing three times every three seconds. 

 

If the device is enabled, when changing the batteries or pressing the «reset» button 
on the top of the device, do not perform step 3

 

 

 

If after turning off the device the SIM-card has been changed to another one, repeat 
all steps, i. e. re-activate the device

 

 

Summary of Contents for M-300






























Reviews: