VeEX VePAL TX300M User Manual Download Page 302

Page: 302 / 421

15.3 RFC 2544 Conformance Testing

Overview
Setup - Standard Mode

Header Settings
Frames Settings
Threshold Settings
Peer-to-Peer Asymmetric Testing

Asymmetric Testing Setup

Throughput Settings
Latency Settings
Frame Loss Settings
Burst Settings

Starting / Stopping a RFC2544 Measurement
Results - Standard Mode

Status
Summary
Signal
Events
Latency / Jitter
Frame Loss
Burst

Saving Results
Advanced SLA Mode

Background General Setup
Background Traffic Setup
Background Results

Overview:

RFC 2544 recommendations are well accepted in the test and measurement industry for network performance testing. The RFC

2544 test suite consists of and performs a set of four automated tests (throughput, latency, frame loss, and burst or back-to-back)

to qualify the performance of a network link under test. The tests are especially popular for the verification of network links with

certain service level agreements (SLA).

The following settings must be configured prior to RFC 2544 testing:

Test layer (Layer 2, 3, & 4)

Frame header (PBB, MAC, VLAN, IP, UDP, and Data)

Test frames selection

Pass/fail thresholds (optional)

Far-end unit loop control

Throughput

Latency

Frame loss

Burst (back-to-back)

RFC 2544 Setup - Layer 2 parameters

TX300S_e-manual_D07-00-064P_RevA00

Summary of Contents for VePAL TX300M






































































































































































































































































































































































































































Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands

VeEX VePAL TX300M, User Manual

Search results

Summary of Contents for VePAL TX300M

Reviews:

Related manuals for VePAL TX300M

Brands by name

Popular brands