background image

1

Introduction

This manual covers Transducer Replacement Instructions for Veeder-Root Wireless 
Pressurized Line Leak Detection (WPLLD) Systems.

Safety Symbols

The following safety symbols may be used throughout this manual to alert you to 
important safety hazards and precautions.

Explosive

Fuels and their vapors are extremely explosive if ignited.

Flammable

Fuels and their vapors are extremely flammable.

Electricity

High voltage exists in, and is supplied to, the device. A potential shock hazard exists.

Turn Power Off

Live power to a device creates a potential shock hazard. Always turn power off to the 
device and associated accessories when servicing the unit.

No Power Tools

Sparks from power tools (such as drills) can ignite fuels and their vapors.

Use Safety Barricades

Unauthorized people or vehicles in the work area are dangerous. Always use safety 
cones or barricades, safety tape, and your vehicle to block the work area.

Read All Related Manuals

Knowledge of all related procedures before you begin work is important. Read and 
understand all manuals thoroughly. If you do not understand a procedure, ask someone 
who does.

OFF

Summary of Contents for WPLLD













Reviews: