background image

1-1

1  

Introduction

This manual contains instructions on how to install the Veeder-Root Wireless Pressurized Line Leak Detection (WPLLD) 
System for use with TLS-350 Series Consoles. WPLLD sensors can be used with FE Petro

 or Red Jacket

 Pumps that 

have up to a 2-inch discharge.

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 
equipment discussed in this manual:

Level 1

Contractors holding valid Level 1 Certification are approved to perform wiring and conduit routing, 

equipment mounting, probe and sensor installation, tank and line preparation, and line leak detector installation.

Level 2/3

Contractors holding valid Level 2 or 3 Certifications are approved to perform installation checkout, 

startup, programming and operations training, troubleshooting and servicing for all Veeder-Root Tank Monitoring 
Systems, including Line Leak Detection and associated accessories.

Warranty Registrations may only be submitted by selected Distributors. 

Related Manuals

576013-879

TLS-3XX Series Site Prep and Installation Manual

577013-465

Line Leak Application Guide

577013-481

WPLLD Modules- Installation Manual

577013-727

WPLLD Alarm Quick Help Guide

Safety Precautions

The following safety symbols are used throughout this manual to alert you to important safety hazards and precautions. 
Know what these symbols mean before using this manual to install the WPLLD system.

EXPLOSIVE
Fuels and their vapors are extremely 
explosive if ignited.

FLAMMABLE
Fuels and their vapors are extremely flamma-
ble.

ELECTRICITY
High voltage exists in, and is supplied 
to, the device. A potential shock haz-
ard exists.

TURN POWER OFF
Live power to a device creates a potential 
shock hazard. Turn Off power to the device and 
associated accessories when servicing the 
unit.

CLEAN WORK AREA
Dispose of fuel soaked materials 
properly and not into trash barrels 
that may be used by customers.

APPROVED CONTAINERS
Use nonbreakable, clearly marked containers, 
suitable for collecting and transporting hazard-
ous fuels during service.

WARNING
Heed the adjacent instructions to 
avoid equipment damage or personal 
injury.

OFF

G
    A
       S

Summary of Contents for WPLLD







































Reviews: