background image

Introduction

Related Manuals

2

Related Manuals

The manuals in Table 1 below are shipped with the equipment on the V-R Tech Docs CD-ROM and will be needed 
to install specific equipment.

Safety Precautions

The following symbols may be used throughout this manual to alert you to important safety hazards.

Table 1. Related Manuals

V-R Manual

Part Number

TLS-3XX Site Prep Manual

576013-879

Vapor Pressure Sensor For Vent Stacks Installation Guide 
(For Sensor P/N 861190-X0X)

577014-019 

Pressure Sensor Installation Guide 
(For Sensor P/N 331946-001)

577013-797

TLS-3XX Series Consoles System Setup Manual

576013-623

TLS-3XX Series Consoles Operator’s Manual

576013-610

Serial Comm Modules Installation Guide

577013-528

TLS-350 Series Board and Software Replacement Manual

576013-637

ELECTRICITY

High voltage exists in, and is sup-
plied to, the device. A potential 
shock hazard exists.

TURN POWER OFF

Live power to a device creates a 
potential shock hazard. Turn Off 
power to the device and associ-
ated accessories when servicing 
the unit.

READ ALL RELATED MANUALS

Knowledge of all related proce-
dures before you begin work is 
important. Read and understand 
all manuals thoroughly. If you do 
not understand a procedure, ask 
someone who does.

WARNING

Heed the adjacent instructions to 
avoid equipment damage or per-
sonal injury.

WARNING

The console contains high voltages which can be lethal. It is also connected to 
low power devices that must be kept intrinsically safe.

Turn power Off at the circuit breaker. Do not connect the console AC power 
supply until all devices are installed.

FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY 
PRECAUTIONS COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, 
RESULTING IN SERIOUS INJURY OR DEATH.

OFF

OFF

Summary of Contents for TLS




























Reviews: