background image

 VPS Installation

Safety Precautions

3

3

Safety Precautions

The following safety symbols may be used throughout this manual to alert you to important safety hazards and 

precautions.

EXPLOSIVE

Fuels and their vapors are extremely explosive if 

ignited.

FLAMMABLE

Fuels and their vapors are extremely flammable.

ELECTRICITY

High voltage exists in, and is supplied to, the 

device. A potential shock hazard exists.

TURN POWER OFF

Live power to a device creates a potential shock 

hazard. Turn Off power to the device and associated 

accessories when servicing the unit.

WARNING

 

indicates a hazardous situation 

which, if not avoided, could result in death or 

serious injury.

USE SAFETY BARRICADES

Unauthorized people or vehicles in the work area are 

dangerous. Always use safety cones or barricades, 

safety tape, and your vehicle to block the work area.

READ ALL RELATED MANUALS

Knowledge of all related procedures before you 

begin work is important. Read and understand all 

manuals thoroughly. If you do not understand a 

procedure, ask someone who does.

NOTICE

 is used to address practices not related 

to physical injury.

WARNING

This product is to be installed and operated in the highly combustible 

environment of a gasoline dispenser where flammable liquids and explosive 

vapors may be present.
FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS AND SAFETY 

PRECAUTIONS COULD CAUSE DAMAGE TO PROPERTY, ENVIRONMENT, 

RESULTING IN SERIOUS INJURY OR DEATH.
The following hazards exist:

1. Electrical shock resulting in serious injury or death may result if power is 

on during installation and the device is improperly installed.

2. Product leakage could cause severe environmental damage or explosion 

resulting in death, serious personal injury, property loss and equipment 

damage.

Observe the following precautions:

1. Read and follow all instructions in this manual, including all safety 

warnings.

2. To be installed in accordance with the National Electrical Code (NFPA 70) 

and the Code for Motor Fuel Dispensing Facilities and Repair Garages 

(NFPA 30A).

3. Before installing this device, turn Off, tag/lock out power to the system, 

including console and submersible pumps. 

4. To protect yourself and others from being struck by vehicles, block off 

your work area during installation or service.

5. Substitution of components may impair intrinsic safety.

Summary of Contents for TLS-3 Series























Reviews: