background image

1

  VPS Installation

This manual contains instructions to install a Veeder-Root (In-Station Diagnostic) Vapor Pressure Sensor (VPS) in 

the dispenser vapor return line or in a vapor vent stack enclosure. 

For a VPS sensor that will be direct wired to a TLS console, this manual assumes all preliminary site preparation is 

completed, and that wiring from the console to a VPS intrinsically-safe junction box is in place and meets the 

requirements set out in the appropriate console Site Prep manual.

For wireless VPS sensor installations, follow the steps herein to install the VPS sensor itself, but refer to manual 

577013-964 for installation of, and connection to, the wireless components.

Installation of the VPS on the vapor vent stack is only allowed at facilities equipped with a

“Veeder-Root Vapor Polisher” or “Franklin Fueling System Healy Clean Air Separator.

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and set up the 

equipment discussed in this manual:

All service personel on site must comply with all recommended safety practices identified by OSHA and your employer.
Review and comply with all the safety warnings in this an any related documents, and any other Federal, State, or Local 
requirements

Warranty Registrations

 may only be submitted by selected Distributors.

Veeder-Root Contractor 

Certification Requirements

Installer 

Certification

6

ATG Technician 

Certification

7

VR Vapor Products 

Certification

8

TLS-450PLUS

EVR for CA

Certification

Install

ISD

X

X

X

X

Install PMC

X

X

X

X

Install CCVP

X

X

X

X

Install Wireless ISD/PMC

X

X

X

X

Installation Checkout

2

X

X

X

ATG Startup

3

 / Training

4

 / Service

5

X

X

X

ISD Startup / Training / Service

X

X

PMC Startup / Training / Service

X

X

CCVP Startup / Training / Service

X

X

Wireless ISD/PMC Startup / Training / Service

X

X

Install Pressure Sensor (ATG)

X

X

X

X

Maintain Pressure Sensor (ATG)

X

X

X

Calibrate Pressure Sensor (ATG)

X

X

X

Clear ATG Pressure Sensor Alarm (ATG)

X

X

X

Clear ISD/PMC Alarms (ISD/PMC)

X

X

1

Perform wiring and conduit touting; equipment mounting 

2

Inspect wiring and conduit routing; equipment mounting

3

Turn power on, program and test the systems

4

Provide supervised field experience in service techniques and operations

5

Troubleshoot and provide routing maintenance

6

UST Monitoring Systems – Installer (Level 1)

7

Certified UST Monitoring Technician

8

VR Vapor Products

Summary of Contents for TLS-3 Series























Reviews: