background image

1

  Introduction

This manual contains instructions for replacing the right front door LCD display in the following consoles:

• TLS-300 (all versions)

• TLS-350 (all versions)

• EMC (all versions)

• ProPlus and ProMax 

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 
equipment discussed in this manual:

Installer Certification (Level 1):

 Contractors holding valid Installer Certification are approved to perform wiring 

and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless 
equipment installation; tank and line preparation; and line leak detector installation.

Technician Certification (Level 2/3):

 Contractors holding valid Technician Certifications are approved to 

perform installation checkout, startup, programming and operations training, system tests, troubleshooting and 
servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak Detection. In addition, 
Contractors with the following sub-certification designations are approved to perform installation checkout, startup, 
programming, system tests, troubleshooting, service techniques and operations training on the designated system. 

• Wireless 2
• Tall Tank

VR Vapor Products Certification:

 Contractors holding a certification with the following designations are 

approved to perform installation checkout, startup, programming, system tests, troubleshooting, service techniques 
and operations training on the designated system. 

• ISD – In Station Diagnostics
• PMC – Pressure Management Control
• CCVP - Veeder-Root Vapor Polisher
• Wireless – ISD/PMC Wireless
• A current Veeder-Root Technician Certification is a prerequisite for the VR Vapor Products course. 

Warranty Registrations

 may only be submitted by selected Distributors.

Safety Precautions

The following safety symbols may be used throughout this manual to alert you to important safety hazards and 
precautions.

ELECTRICITY
High voltage exists in, and is supplied to, 
the device. A potential shock hazard exists.

TURN POWER OFF
Live power to a device creates a potential shock 
hazard. Turn Off power to the device and associ-
ated accessories when servicing the unit.

OFF

Summary of Contents for TLS-3 Series










Reviews: