background image

 

 

TLC3-FCR-2T Engineering Manual

 

 

Doc: 70-00-0202, V3.0 Date: 20121119 

© Vector Controls GmbH, Switzerland 

Page 8 

Subject to alteration 

Control configuration  

Identifying the firmware version 

The parameters and functionality of controller depend on its firmware revision. It is therefore important to use a 

matching product version and parameter set. The firmware version is shown on the large LCD digits when pressing UP 

and DOWN buttons for more than 3 seconds simultaneously.  

Control Parameters (Access code: 241) 

Warning! Only experts should change these settings! See user parameters for login procedure.  

Parameter 

Description 

Range 

Standard 

FC 00 

Minimum setpoint limit in Heating mode 

-40…60°C (160°F) 

16°C (61°F) 

FC 01 

Maximum setpoint limit in Heating mode 

-40…60°C (160°F) 

24°C (75°F) 

FC 02 

Minimum setpoint limit in Cooling mode 

-40…60°C (160°F) 

18°C (64°F) 

FC 03 

Maximum setpoint limit in Cooling mode 

-40…60°C (160°F) 

30°C (86°F) 

Controls configuration 

FC 04 

Economy (unoccupied) Mode temperature shift: 
The comfort (occupied) setpoint is shifted by the value 
set with parameter. If heating is active the comfort 

setpoint will be decreased, if cooling is active, the 

setpoint will be increased. (Enable with UP06.) 

0…10.0°C (20.0°F) 

5.0°C (10°F) 

FC 05 

Switching Span Heating,  

Setting this value to 0 disables the auto fan speed 

function in heating mode 

0…10.0°C (20.0°F) 

1.5°C (3°F) 

FC 06 

Switching Span Cooling 

Setting this value to 0 disables the auto fan speed 

function in cooling mode 

0…10.0°C (20.0°F) 

1.0°C (2°F) 

FC 07 

Switching Hysteresis is the difference between switching 

on and switching off. A small hysteresis will increase the 

number of switching cycles and thus the wear on fan and 

relays contacts. 

0…10.0°C (20.0°F) 

0.5°C (1°F) 

FC 08 

Mold Protection:  

In mold protection, the fan keeps running independent of 

temperature as long as the unit is switched on. 

ON, OFF 

OFF 

FC 09 

Switching delay min running time of fan speed 

0…255s 

10s 

FC 10 

Switching delay min stopping  time of fan speed 

0…255s 

10s 

FC 11 

Control option:  
0 = Cooling only 

1 = Heating only 

2 = 2-pipe system 

3 = 4-pipe system  

0…3 

Default = 3 

W01 = 0 
W02 = 1 

W03 = 2 

W04 = 3 

FC 12 

Dead Zone Span: 
The Dead Zone Span lies between the heating and the 

cooling setpoint. The output is off while the temperature 

is within the dead zone span. A negative dead zone is not 

possible. 

0…10.0°C (20.0°F) 

1.0°C (2°F) 

FC 13 

Heat/Cool Changeover Delay (if set to FC11 = 3): 
A demand to switch between heating and cooling must 

persist for the length of time set with this parameter 

before the controller switches. Prevents activation of a 

sequence during a short-term change in temperature in 

order to protect equipment (with control overshoot for 

example) 

0…255 min 

5 min 

 

 

Summary of Contents for TLC3-FCR-2T











Reviews: