VDO Ocean Line Sumlog Page 20 Manual Download

Page: 20 / 21

INSTALLATION / DATA

Circuit diagram legend:

On/Off switch for navigation instruments

On/Off switch for instrument lighting

Fuse for navigation instruments (5 A)

Fuse for instrument lighting (5 A)

Recommended cable section: 1.5 mm

Cable lengths:

Log sending unit - Indicating instrument

20 m max.

Indicating instrument - Repeater

10 m max.

Repeater 1 - Repeater 2

10 m max.

Technical data:

Measuring principle:

Pulse count by Hall sensor

Supply voltage:

10.8 V to 32 V DC

Current consumption:

about 100 mA at 12 V DC (without illumi-
nation), about 260 mA with illumination

Operating temperature:

-10 °C to +60 °C

Type of protection:

DIN 40050 - IP 65 at front

EMC protection:

CE: EN 50081-1, EN 50082-1

Dimensions:

Indicating instrument:
Front ring diameter

105 mm

Installation diameter

86 mm

Installation depth

56 mm (union nut)

Installation depth

90 mm (bracket)

Hull sleeve:
Installation diameter:

39 mm

Maximum hull thickness:

30 mm

Technical modifications reserved

Summary of Contents for Ocean Line Sumlog






















Search results

Summary of Contents for Ocean Line Sumlog

Reviews:

Related manuals for Ocean Line Sumlog

Brands by name

Popular brands

VDO Ocean Line Sumlog, Manual

Search results

Summary of Contents for Ocean Line Sumlog

Reviews:

Related manuals for Ocean Line Sumlog

Brands by name

Popular brands