background image

Notes on operating instructions

The following reading aids are used to simplify these operating instructions:

Requests you to perform an action.

Provides additional information.

Identifies a list.

6

Shows that the current topic is continued on the following page.

A

Safety instructions and warnings contain important information for the safe use of the unit.

Failure to observe this information may result in a risk of damage or injury. Therefore, please ob-
serve this information with particular care.

WARNING: Important information for safe operation

A

For safety reasons, the driver should not watch television or operate a video source (DVD

player, TV tuner, etc.) when driving. Please note that it is illegal in certain countries to watch or
operate the television when driving.

A

When setting the volume, please make sure that traffic noises (horns, sirens, emergency

vehicles, etc.) are still audible.

Features

2 audio / video inputs (RCA/Cinch).

2 independent monitor outputs.

Automatic switching of video sources for monitor 1.

Navigation and reversing camera input for monitor 1.

Volume control of connected video sources.

Optional RST 5400 Rear Seat Terminal connection.

Function

The MI 2200 multimedia interface enables building of a multimedia system, with little effort.
For this purpose, any video sources (e.g. VDO Dayton DVD player DV 6100), a VDO Dayton
reversing camera as well as a navigation computer can be connected to the MI 2200.
AV sources are selected via the supplied infrared remote control. For monitor 1, switching of
the relevant video source (AV, reversing camera or navigation system) is performed
automatically by the MI 2200, depending upon the driving situation.

Monitor stand-by

The MI 2200 is switched on and off together with the ignition (ACC / accessory contact). The
monitors are automatically switched into standby mode after startup. Only if a navigation
system and / or a reversing camera is installed, will monitor 1 be switched on, provided one
of these AV sources is active.

k

GENERAL INFORMATION

5

English

Summary of Contents for MI 2200












Reviews: