background image

GB

5

Caution: Take care not to drill into the fuel tank, the exhaust pipe system, the catalytic
converter or the cables laying behind or below any drilled holes!

• To prevent dust and dirt entering the unit, glue the supplied stickers over all unused

mounting holes of the CD changer (see Figs. 10 and 18).

MOUNTING IN THE LUGGAGE BOOT

Fix brackets A (L) and (R) to the lower sides of the CD changer using the hexagonal bolts C
(Figs. 10, 11 or 12).
Fix the base-plates with the long hexagonal bolts to the brackets using the hexagonal nuts D
(Fig. 13).
If present, lift the carpet covering the floor of the luggage boot.

First glue the supplied double-sided self-adhesive tape to the base plates. Then carefully
position the CD changer and apply pressure to glue it into place (Fig. 14). The base plates
must be glued to a clean, flat surface.

If there is no flat surface in the luggage boot, a wooden mounting board (approx. 10 mm
thick) under the carpet should be used instead of the base plates. (Fix the wooden mounting
board to the car using three screws). In that case fix the brackets to the board (laying under
the carpet) using screws.

Remove the hexagonal nuts D. Lift up the CD changer (Fig. 15).

Lay the carpet over the base-plates (or the wooden mounting board) and cut four small
crosses in the carpet. Press through the threaded studs (Fig. 16).
Check that the three transport screws have been removed from the underside of the CD
changer!
Mount the CD changer using the hexagonal nuts D (Fig. 17).

MOUNTING IN SUSPENDED POSITION

The CD changer can also be mounted on the underside of a flat surface, e.g. the rear parcel
shelf.

Fix brackets A (L) and (R) to the upper sides of the CD changer using the hexagonal bolts C
(Fig. 18).
Place the CD changer in the mounting position (Fig. 19).

Mark positions for four mounting holes (with a felt-tip pen).

Drill holes of 3.6 mm diameter in the marked positions.

Check that the three transport screws have been removed from the underside of the CD
changer!
Hold the CD changer in place and attach it with the tapping screws E.

6

5

4

3

2

1

4

3

2

1

4

3

2

1

MOUNTING

A

CH0600/1000 GB  30/07/99 14:00  Page 5

Summary of Contents for CH0600, CH1000










Reviews: