background image

Page 4 / 5

Functions and Operations (continued)

221021

4. PC MODE (nighttime operation only)

    ● In "PC" mode, the light will turn on at full brightness at dusk and remains on until dawn.

       

5. 3 HOURS (3H) MODE (nighttime operation only)

    ● In “3H” mode, the light turns to high-level brightness at dusk, and stays "ON" for 3 hours, then it turns to low-level

        brightness. It turns to high-level brightness when motion is detected, and stays on as long as motion continues. 

        When motion is no longer detected, it remains on for the predetermined shut-off delay time you set (30s/1min/3min), 

        then returns to the low-level brightness automatically.

     ● The light turns off automatically at dawn.

6. CUSTOM SETTING MODE (nighttime operation only):

    ● In "CUSTOM SETTING" mode, the light turn on at dusk and off at dawn automatically.

    

 

Instead of "3H", the motion sensor operation can be set to start at a specific time. Turn the wall switch “OFF”, and

       turn it “ON” twice within 3 seconds. The light will go into motion-sensor operation at the specified time every night. 

       The light turns off automatically at dawn.

       For example, a homeowner wants to have the light stay on high-level brightness from dusk to 8pm, and would like

       the light to go into "AUTO motion sensor mode. 

       To achieve this, the homeowner will turn the wall switch “OFF”, and turn it “ON” twice within 3 seconds. This sets 

       the time the light goes into "AUTO" mode every day, the light will behave the same way.

       To revert back to Default, turn the wall switch “OFF” and then

       turn it “ON” after 5 seconds.

7. Manual Override (nighttime operation only)

   

 ● To temporarily override the settings in 

“OFF” or “AUTO”

        or “3H” mode for on-demand continuous high-level 

        brightness at night, turn the wall switch “OFF” then turn it 

        “ON” twice within 3 seconds, the light remains on all night long.

        To shift back to “OFF” or “AUTO”  or “3H” mode, turn the wall

        switch “OFF” then turn it “ON” twice within 3 seconds again.

        (See Fig.6)

    ● The light turns off automatically at dawn.

    Note: To make sure the above functions operate properly,  

    always keep the wall switch in the “ON” position (including 

    the daytime).

       

 

Fig.6

“AUTO” “OFF” 

or “3H” Mode

 Manual

Override

Manual Override Operation Diagram

Turn wall switch OFF-ON-OFF-ON 

in 0.5~3 Seconds 

 

Turn wall switch OFF-ON-OFF-ON 

in 0.5~3 Seconds 

Customization Options:

Shut-off Delay

● The shut-off delay is the length of time the light will stay at

    brightness after motion is detected.

● You can set the shut-off delay by rotating the Time knob arrow 

    so it points to the desired time setting 

    (

30s/1min/3min

). To increase the shut-off delay, turn the knob 

    clockwise. To decrease the shut-off delay, turn the knob 

    counterclockwise.

     

Notes:

1. The sensitivity of the motion sensor will increase as the 

    environmental temperature gets cooler.  For best performance, 

    gently clean the lens with a soft cloth every 1 or 2 months to 

    ensure maximum sensitivity.

2. For best performance, install fixture at least 8 feet above the 

    ground. At such a height, the fixture will provide a detection 

    distance of up to 70 feet at 77 degrees Fahrenheit. (See Fig.7)

3. The sensor detects movement across a detection range of 180 degrees. (See Fig.8)

4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.9)

5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace 

    exhaust, or in a direction facing any reflective object or other nearby light source.

Fig. 7

Fig.8

10'

8.0'

12.0'

70'

Where you install your fixture is important:

Be sure the light is mounted straight on the wall 

or eave; otherwise, the detection distance may 

be limited. 

180˚

Fig.9

Motion

Least sensitive

Motion

Most sensitive

Sensor

Summary of Contents for T0694






Reviews: