background image

Page 1 / 5

Important to Know:

1. If you are not familiar with state and local electrical

  codes, it is recommended that you consult with a

  qualified electrician.

2. This fixture requires a 120 VAC, 60 Hz power

  source. 

3. For general safety and to avoid any possible 

  damage to the sensor, be sure the power is

  switched "off" before adjustment.

Maximum Wattage: 2-150 W (bulb not included)

Working Temperature Range: - 13

°F ~ 113°F

ASSEMBLY  AND  INSTALLATION 

                INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

               2. READ AND SAVE THESE INSTRUCTIONS.

T0694 / T0695

Features:

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted. 

Wall Mounted 

Eave Mounted

Read notes section on page 4 for additional information about mounting location of fixture.

Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for 

proper operation and to avoid the risk of electrical shock.

1. Motion sensor: turns light ON automatically when 

    motion is detected and turns light OFF or remains 

    Low-level brightness when motion stops.

2. Photocell keeps the light OFF during daylight hours.

Hardware Package (included):

Decorative cover

Fixture Mounting Screw

Mounting Strap

Wire Connector

Gasket 

Mounting Screw X2

#8/32X1/2 in

Mounting Screw X2

#6/32 X1/2 in

Mounting Screw X2

#10/24 X1/4 in

For eave mounted only:

Rotate the sensor head towards the back plate.

Rotate the sensor head clockwise 180˚ so the controls face down.

Controls

Backplate

Controls

Controls

221021

Summary of Contents for T0694






Reviews: