Vaxcel T0622 Assembly And Installation Instructions Manual Download Page 3

 

Sensor Adjustment Lower For Short Coverage

Sensor Adjustment  Higher For Long Coverage

Fig. 4

1. Gently grasp the light heads and tilt them up or down, left or right to 

DGMXVWWKHOLJKWFRYHUDJHDUHD.HHSWKHOLJKWKHDGVDWOHDVWÝPP

    away from the sensor.(See Fig. 4)

2. 

.HHSWKHOLJKWKHDGVÛEHORZKRUL]RQWDOWRDYRLGZDWHUGDPDJHDQG

    electrical shock.

Fig. 2

Fig. 3

Adjusting the Light Head: 

Sensitivity of Motion Sensor: 

1. You can adjust the sensitivity of the motion sensor by using the “Sens” selector  located on the bottom surface of the 
    sensor. 

 2. Adjust motion sensor sensitivity to HIGH (H), MEDIUM (M), or LOW (L) to achieve desired performance. 
   
 3. Approximate range for each setting: 30 ft. (L), 50 ft. (M), 70 ft. (H).

Choose a mode by sliding the switch on the bottom of the sensor.  (See Fig.5)

Note: When power is first applied, the light will turn on to 100% brightness.
The sensor will take 30 seconds to warm up.

   

1. 

TEST MODE (daytime and nighttime operation.)

Ɣ6OLGHWKH7LPHVZLWFKWKH³7HVW´SRVLWLRQ

Ɣ7KHOLJKWWXUQVWRKLJKOHYHOEULJKWQHVV.ZKHQPRWLRQLVGHWHFWHGDQGVWD\VRQDVORQJDVWKHPRWLRQ

       continues. 
       Then it revert back to 2700K CCT Color and the low-level brightness (0~50%) as per setting about 5 seconds 
       after motion is no longer detected.

2. 

 AUTO MODE (nighttime operation only)

Ɣ7R³$872´PRGH

 

slide the Time switch to the desired time setting 

        (30s/1min/3min). At dusk, the light turns on to pre-selected low-level 
        brightness (2700K). When motion is detected, the light turns to high-level 
        brightness (5000K) and stays on as long as motion continues. When the 
        motion is no longer detected, the light at high-level brightness (5000K) 
        remains on for the predetermined time you set (30s/1min/3min), then 
        switches back to pre-selected low-level brightness (2700K) automatically. 

Ɣ7KHOLJKWWXUQVRIIDXWRPDWLFDOO\DWGDZQ

     Note: You can adjust the low-level brightness(0~50%) by using the low-level brightness(0~50%) knob on
     the backplate (See Fig.6).

3. 

PC MODE (nighttime operation only)

Ɣ,Q3&PRGHWKHOLJKWZLOOWXUQRQDWIXOOEULJKWQHVV.DWGXVNDQGUHPDLQVRQXQWLOGDZQ

Page 3  /  17

211231

Summary of Contents for T0622


















Reviews: