Vax Oasis Complete V-133 Instruction Manual Download Page 8 | Manualshive

Page: 8 / 20

Vax Oasis Complete V-133 Instruction Manual Download Page 8

www.vax.co.uk

8

operation

Carry tank to a sink. Rotate tank cap counterclockwise and
lift up to remove cap (Fig4/9).

Turn cap upside down to serve as a measuring cup
(Fig4/10).

Using cap, measure detergent following the chart
below.

For carpet, carpeted stairs and upholstery:

Fill cap to fill line (150ml) with Vax Carpet/Upholstery
Detergent.

For bare floors:

Fill cap to fill line (150ml) with Floor-2-Floor Cleaning
Solution.

IMPORTANT:

Do not use Hard Floor Cleaning

Solution on carpet or upholstery. Do not use any

type of wax with your Oasis SpinPower carpet cleaner.

NOTE:

Use only Vax detergents. They are specially

formulated for use with your Oasis SpinPower carpet
cleaner.

Pour detergent into tank. Fill tank to fill line (4L approx)
with hot tap water. To assure proper performance, use
only Vax cleaning detergent (Fig4/11).

If rubber ring on cap has become dislodged, reposition it
with uneven side against ledge as shown (Fig4/12).

Replace cap. Rotate cap clockwise until it locks in place.

NOTE:

Cap must be locked in place for proper performance

and to prevent leaking (Fig4/13).

Fig.4/9

Fig.4/11

Fig.4/12

Fig.4/13

Fig.4/1

Fig.4/10

150ml

Rubber ring

Ledge

Fill line

!

V-133 OasisComp User Guide v5.qxd:V-133 Oasis User Guide 8/9/08 14:44 Page 8

«
...
6
7
8
9
10
...
»

Summary of Contents for Oasis Complete V-133





















Reviews:

No comments