Vax Mach3 U90-M3 series Instruction Manual Download | Manualshive

Page: 16 / 16

background image

EEC STATEMENT OF COMPLIANCE

Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the

VZL-6013 Mach 3 Range and VZL-6014 Mach 4 Range upright vacuum cleaners

are manufactured in compliance with the following Directives:

Safety:

2006/95/EC Low Voltage Directive

EMC:

2004/108/EC Electromagnetic Compatibility Directive

Waste electrical products should not be disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for recycling advice.

Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK

email:

[email protected]

- website:

www.vax.co.uk

«
...
14
15
16

Summary of Contents for Mach3 U90-M3 series

















Reviews:

No comments

Related manuals for Mach3 U90-M3 series

Brand: Samsung Pages: 20

Brand: Samsung Pages: 16

Brand: Hilti Pages: 144

Brand: Bionaire Pages: 2

2950-2996 Series

Brand: Eureka Pages: 8

Brand: InterVac Pages: 10

Brand: eta Pages: 60

Brand: EarthLinked Pages: 16

Tornado Essential

Brand: Daewoo Pages: 9

Brand: Vax Pages: 4

Brand: Vax Pages: 12

Brand: Symbo Pages: 84

Brand: King Industrial Pages: 6

Brand: Easy@Home Pages: 46

Brand: cecotec Pages: 141

Brand: BestAir Pages: 14

Brand: Gorenje Pages: 156

Brand: Hanseatic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands