Vehicle features
Front seat adjustment:
1. Backrest rake
2. Seat height
3. Thigh support
3
Press button on side of head restraint to
release and adjust height.
Front seat adjustment:
4. Lumbar support
3
5. Inclination
3
6. Positioning
Important:
Do not sit nearer than
10 inches (25cm) from steering wheel, to
permit safe airbag deployment.
Steering wheel adjustment:
Move lever down, adjust height and
distance, move lever up, engage into
position.
Adjust steering wheel only when vehicle
is stationary and steering column lock is
released.
Adjusting exterior mirrors:
Outer mirror switch pressed: four-way
switch adjusts driver’s and passenger’s
mirror. Inner mirror switch pressed: only
front passenger’s mirror is adjusted.
Electric seat adjustment with
Memory function
3
: Select reverse gear
with inner mirror switch pressed; front
passenger’s mirror points to rear tyres
as a parking aid.
Automatic anti-dazzle mirror on driver’s
side
3
: Dazzle at night is reduced.
Swing-in exterior mirrors
3
:
Push four-way switch to the right:
Exterior mirrors swivel in.
Push four-way switch to the left:
Exterior mirrors swivel out.
Swivelling allowed upto speeds of 4 mph.
If necessary, the exterior mirrors can be
swivelled manually: Press outer edge of
mirror housing gently.
Driving with swivelled-in exterior mirrors
is not permitted.
Fitting seat belt:
Draw seat belt smoothly from inertia
reel, guide over shoulder and engage in
belt buckle.
The belt must not be twisted at any
point. The lap belt must lie snugly
against the body.
The front seat backrests must not be
tilted back too far (recommended
maximum tilting angle approx. 25
o
).
To release belt, press button on buckle.
Light switch:
0
= Off
8
= Parking lights
9
= Dipped or main beam
AUTO
= Automatic dipped beam
activation
3
Light switch (continued):
0
= Courtesy light
>
= Front fog lights
3
r
= Fog tail light
k
= Instrument illumination
?
= Headlight range adjustment:
Reduces dazzle for oncoming traffic.
Manual headlight range adjustment:
Without level control system
0 = Front seats occupied only
1 = All seats occupied
2 = All seats and luggage
3 = Driver’s seat only and luggage
With level control system
3
0 = Front seats occupied
1 = All seats occupied
1 = All seats and luggage
2 = Driver’s seat only and luggage
Switching to dipped or main beam:
Main beam
= Push stalk forward.
Dipped beam = Push forward again.
To operate the headlight flash, pull stalk
towards the steering wheel.
Door-to-door lighting
3
:
Dipped beam and reversing lights
illuminate for approx. 30 seconds after
closing driver's door.
To activate: Switch ignition off, remove
key, open driver’s door and pull turn
signal stalk towards steering wheel.
If driver's door is left open, lights will go
out after two minutes.
Cancel by inserting key in starter switch
or pull turn signal stalk to steering wheel.
Turn signal lights:
Right
= Stalk all the way up
Left
= Stalk all the way down
The turn signal stalk returns to its
original position after use. When the
steering wheel is straightened up, the
turn signal lights are automatically
cancelled.
When lane changing, tap stalk until
resistance is felt: the turn signals will
flash three times.
Parking lights:
Front parking lights and tail lights can be
switched on at one side when parking:
Light switch to position
0
, switch ignition
off, move turn signal stalk fully upwards
(right parking light) or downwards (left
parking light).
An acoustic signal sounds and the turn
signal control indicator on the respective
side illuminates.To switch parking lights
off, switch on ignition or move stalk in
opposite direction.
Windscreen wiper:
Gently tap stalk upwards.
Gently push stalk upwards.
§
= Off
$
= Adjustable timed interval wipe
%
= Slow
&
= Fast
Stalk always moves back to the starting
position. To select the next higher or
lower stage: move stalk slightly.
Push stalk past resistance point and
hold: wiper stages are run through; an
acoustic signal sounds at position
§
.
Adjustable timed interval wipe
$
:
Adjuster wheel right = Short intervals,
Adjuster wheel left = Long intervals.
Stalk down from position
§
: Single wipe.
Automatic wiping with rain sensor
3
:
Gently push stalk upwards.
§
= Off
$
= Automatic wiping with rain sensor
The rain sensor detects the amount of
water on the windscreen and
automatically controls the windscreen
wiper.
Adjust the sensitivity of the system using
the adjuster wheel:
Adjuster wheel right = High sensitivity,
Adjuster wheel left = Low sensitivity.
Keep the sensor area clean by operating
the windscreen wash system regularly.
Windscreen wash system and headlight
wash system
3
:
Pull stalk towards steering wheel.
The wiper is switched on for several wipe
operations. A single after-wipe occurs at
low speeds.
The headlight wash system
3
is ready for
operation when the headlights are
switched on. Wash fluid is sprayed onto
the headlights once. Then the headlight
wash system is disabled for 2 minutes.
On vehicles fitted with rain sensor
3
,
keep the sensor area clean by operating
the windscreen wash system regularly.
Engine oil:
Check every 300 miles and prior to long
journeys.
Important:
It is the owner’s responsibility
to maintain the correct level of an
appropriate quality oil in the engine.
Refuelling:
Use unleaded fuel for petrol engines.
Fuel tank capacity - 60 litres.
Warning:
In freezing conditions, wiper blades can
freeze to the windscreen. Release blades
from the ice before starting the car to
prevent wiper motor damage.
