Vauth-Sagel HSA power move Operating And Installation Manual Download Page 13

13

11.

CLEANING AND MAINTENANCE

The system must be made currentless by removing the plug from the mains socket before any monitoring or cleaning is carried
out on the system.

Do not clean if there is visible damage to the cables, plugs or housings. Have an authorised specialist replace the damaged
parts.

The system can be cleaned using a dry or damp cloth.

12.

DISPOSAL

The product must not be disposed of with domestic waste!
Disposal or recycling of the product must be carried out according to national and local regulations!

13.

MATERIAL DEFECTS AND PRODUCT LIABILITY

¤

The manufacturer is not liable for damage caused by improper handling, wear, maintenance or other actions.

¤

Legal claims from material defects liability become time-barred one year after handover of the goods. A durability guarantee 
is thus not given.

¤

The customer is obliged to fulfil his examination obligation according to § 377 German Commercial Code, including if the 
goods are resold.

¤

The manufacturer has the right to choose between improvement and re-delivery.

¤

The expenses required for later fulfilment are not to be borne by the manufacturer in as far as the expenses are higher due 
to the goods being brought to a location other than the customer's business location after delivery. This does not apply when
the passage corresponds to the good's proper use.

¤

The customer's right of recourse against the manufacturer on account of such claims of material defect liability which are 
made against the ordering party by its clients, is excluded if the customer does not fulfil his examination and notice of non-
conformity.

¤

The customer may only use the goods for the proper purpose and must make sure that the goods are only re-sold to people
who are aware of the product dangers and risks.

¤

The manufacturer's liability according to the legal regulations for damage claims is unlimited if the manufacturer has deli-
berately neglected his duty or is guilty of gross negligence. As far as the manufacturer's neglect of duty is due to simple 
negligence or an important contractual duty has been violated, the damage claim liability is limited to the predictable da-
mage that occurs in comparable cases. Otherwise liability is excluded.

¤

This does not affect liability according to the conditions of the product liability law. Liability on account of culpable injury to 
life, body and health is not affected either.

We reserve the right to make technical changes for reasons of technological progress.

The texts and drawings do not necessarily correspond to the scope of supply or a spare parts order.
Sketches, graphs and drawings are not to scale.

Publisher:

Vauth-Sagel Systemtechnik GmbH & Co. · Neue Straße 27 · D-33034 Brakel-Erkeln · Tel. +49 (0) 5272 601-01 · Fax +49 (0) 5272 601-193

Copies, even extracts, may only be made following agreement with the publisher

All rights reserved

Summary of Contents for HSA power move















Reviews: